Publicité
Les langues disponibles
Les langues disponibles
WAIT 24 HOURS BEFORE PLUGGING IN THE APPLIANCE AND SWITCHING IT ON.
DURING THIS PERIOD, WE RECOMMEND THAT YOU LEAVE THE DOOR OPEN TO
ELIMINATE ANY RESIDUAL ODORS.
BEFORE PLUGGING IN AND FILLING YOUR APPLIANCE
Failure to comply with the above specifications may invalidate the WARRANTY.
Recommendations
The location you have selected for your appliance should:
be unencumbered and well ventilated;
▪
be well away from any heat source and direct
▪
sunlight;
not be too damp (laundry, pantry, bathroom etc.);
▪
have a flat floor;
▪
have a standard and reliable electricity supply
▪
(standard socket to country standards, linked to the
ground), it is NOT recommended to use a multi-
socket or extension lead;
have a surge protector fitted to the electrical outlet;
▪
Away from the microwave oven. Certain microwave
▪
ovens do not have wave interference shield. When
placed within 1 meter vicinity of the appliance, they
may affect the operation of the unit.
Notes
WC46DZSV1 WC54SZSV1 WC2743SSBC models are all built-
in and free-standing type as per the drawings thereafter.
The
appliance
should
temperature is proper. If the temperature is above or below
this range, it will affect the performance of the unit. Placing
in cold or hot temperature conditions may cause appliance
temperatures fluctuating, and it will not reach the ideal one.
Grounding instructions
The unit must be grounded in case of wire leakage.
Grounding reduces the risk of electrical shock. The appliance
is equipped with a power cord having a grounding wire and
plug. The unit plug must be plugged into a properly affixed
and grounded electrical outlet.
Note: In locations where there is frequent lightning, it is
advisable to use surge protectors.
Improper use of the grounding plug can result in the risk of
electric shock. Consult a qualified electrician or service
person if the grounding instructions are not completely
understood.
If the supply cord is damaged, it must be replaced by a
qualified person in order to avoid electrical hazard.
INSTALLATION
be
placed
where
the
INSTALLING YOUR APPLIANCE
Unpack and remove all of the protection and
adhesive strips from the packaging around and
inside the wine cellar.
The unit must be positioned such that the plug is
accessible. Release the power cord. Move your
appliance to its final location. The unit should be
installed
in
compressor will not be subject to physical
contact.
Note: The appliance must be positioned so
that the plug is accessible after installed.
Leveling your appliance
The appliance must be leveled BEFORE loading
your wines or beverage.
Your appliance is equipped with 4 adjustable feet
ambient
INSTALLATION INSTRUCTIONS FOR BUILT
APPLIANCES
1. "Built in" wine cellars are front venting but are
not designed to be fully integrated behind a
joinery door.
2. Please follow the installation diagram when
installing built-in wine cellars. No less than the
minimum installation dimension, or it will affect
the venting of cellar.
3. Built-in wine cellars draw air from right of
ventilation frame and expel through left of
ventilation frame under the front door.
4. "Built in" wine cellars have a power switch
located on the control panel so power point
location is not critical.
5. The wine cellar requires a standard 120
volt/15-amp power.
6. The power cord is 2.0m in length and is fixed
on the right side at the back when looking from
front of cabinet.
7. As with most appliances of today, the unit has
sensitive
electronic
susceptible to damage through lightning and
electricity supply faults. It is therefore advised to
use a power surge protector to avoid problems of
this nature.
a
suitable
place
to facilitate easy leveling. We
recommend that you tighten the
back feet to the maximum and
adjust the front feet to level the
wine cellar.
components
where
the
which
are
Publicité
