Storage Of The Boat; Treatment And Storage; Guarantee Conditions; Boat Repairs - Gumotex Ruby XL Manuel De L'utilisateur

ATTENTION
prior to every use of the boat, check whether it is nece-
ssary to observe any special regulations, restrictions or
rules connected with the river, surface of water or area in
which you aim to operate.
The boat is not designed to be towed behind motorboats,
nor may it be towed otherwise, dragged or in any way
stressed unusually. In case of emergency, use the handle
to at bow of the boat to tow. Sharp edged and pointed
items carried in the boat must be safely wrapped.
place all precious items into a waterproof container and
fasten it to the boat.
Over time, sunlight adversely aff ects the rubber coating
of the boat; therefore, it is advisable to store the boat in
shade each time after use.
CAUTION
•
On large surfaces of water (seas, lakes) pay attention
to water currents and off -shore breezes. Currents and
breezes may make it impossible to return to shore.
•
The infl atable boat should not be used in challen-
ging conditions, such as in reduced visibility (night,
fog, rain).
•
It is necessary to suffi ciently practise abandoning
an overturned boat on calm waters in advance.
Specifi cations of the WW 2 diffi culty grade - moderately
diffi cult:
•
Irregular waves and riffl es, medium rapids, small whirls and
eddies, low vertical drops, small rapids in watercourse with
heavy meandering or poor visibility
•
Regular fl ow and low, regular waves, small rapids, simple
obstacles, frequent meanders and fast current of water.
ATTENTION
pay great attention to your choice of fl otation life-jacket.
The fl otation life-jacket should have a tag bearing details
of its fl otation capabilities and safety certifi cation.
5. Storage of the Boat – See fig. 3
Remove the seats and transom prior to roll-up. Place all small
accessories to the small mesh bag. No sharp object may re-
main in the boat. Clean and dry the boat. Bleed air from all
chambers. The defl ation may be sped up by rolling the boat
towards the valves. Once all air has bled, place the boat on an
even surface and roll up – refer to Fig. 3.
Lay the boat fl at. Fold both side tubes lengthwise so they do
not project outside the contour of the bottom. Now roll the boat
from both ends to the center. Place the folded halves on top
of each other and tie with the compressing strap. Insert the
boat in the transport bag, add the seats, transom and small
accessories. Force the air out of the bag, roll the end of the
bag and tie it with buckles.
6. Treatment and Storage
The rubber surface coating of the boat is sensitive to oils, gas-
oline, toluene, acetone, kerosene and similar thinning agents.
Prior to storing a dirty boat, wash it down with warm soapy
water. Rinse the boat with fresh water after using the boat in
seawater. It is recommended to check the state of the infl ation
valves and the safety relief valves.
If a valve is not air-tight, it is possible to unscrew the valve
body from the boat with the use of a special valvekey and cle-
an its membrane with a strong jet of water or compressed air.
Prior to storage, it is recommended to rub the surface of the
12
boat with an agent intended for the treatment of such surfaces,
which has cleaning properties, and which impregnates the ma-
terial to prevent further dirtying, or which is capable of forming
a protective UVfi lter.
Never use agents containing silicon when treating your boat.
Store the clean and dry product in a dark dry place at a tem-
perature of (15 – 35) °C, at least 1.5 m from any radiant heat
source and out of the reach of rodents. During longterm sto-
rage, it is recommended to infl ate the boat for 24 hours from
time to time to avoid fatiguing the fold lines.
It is also recommended to have the boat serviced by the ma-
nufacturer's authorized service station at least once every two
or three years.
Proper care and treatment of the boat will increase its service
life.
7. guarantee Conditions
The guarantee period is 24 months and is calculated from the
date of sale.
The producer provides cost-free repairs or replacement of
faulty components for material faults or production faults.
The warranty does not cover damage to air chambers due
to higher pressure than the required operational pressure!!!
8. Boat Repairs
You can easily repair a damaged boat yourselves by means of
the accompanying gluing set.
Gluing:
•
mark out the damaged area on the boat and choose an
appropriately sized patch;
•
the surfaces of both patch and place to be glued must be
clean, dry and without traces of old glue;
•
we recommend degreasing both surfaces with acetone in
order to achieve a perfect bond;
•
spread a thin layer of glue on both surfaces to be glued and
repeat this step once the fi rst layer has dried;
•
after the second layer has dried, press the patch fi rmly on
the damaged place, weigh down or use a rolling pin on
a fl at surface.
For minor repairs (punctures), it is possible to re-infl ate the
boat and continue using it after waiting for approx. 30 minutes;
after more serious repairs, you should wait for 24 hours before
using the repaired boat. Complicated repairs should be per-
formed by the manufacturer or at authorized service stations.
Guarantee repairs and post-guarantee repairs are provi-
ded by the manufacturer:
GUMOTEX Coating, s.r.o.
Mládežnická 3062/3a
690 02 Břeclav
Czech Republic
9. Product Disposal Method
The product should be disposed of at municipal waste dispo-
sal sites.