Télécharger Imprimer la page

VOLTCRAFT BC800 Mode D'emploi page 4

Publicité

Les langues disponibles

Les langues disponibles

5.9 Personal safety
Wear eye protection to prevent injuries from explosions or corrosive chemicals while
working with lead-acid batteries.
Risk of explosion! Never operate the product in areas where flammable fumes or gases
are present (e.g. petrol stations).
Explosive / noxious gases may be produced / present during use. Always use the
product in a well-ventilated area.
Have someone nearby in case there is an emergency.
5.10 Lead-acid battery
Keep fresh water, soap and eyewash within reach.
– If battery acid contacts skin or clothes, wash immediately with soap and water.
– Avoid touching eyes. If acid enters eyes, flush with water for 10 minutes and seek
medical help immediately.
5.11 Charger
Risk of personal injury and/or damage to product! Use this charger with sealed lead acid
type rechargeable batteries only.
5.12 Electric vehicles
Electric vehicles may have specific requirements for jump starting procedures.
Always consult the vehicle operating instructions for information about the starter battery.
6 Connection
Important:
– Always disconnect from the mains power supply before connecting or disconnecting
output cables to the battery.
– The rechargeable battery must be disconnected from a vehicle before charging.
6.1 Connecting the cables
Preconditions:
a
Power adaptor is disconnected from mains supply.
1. Connect the output cables to the socket on the power adaptor.
Connect the barrel plug adaptor if needed. See:
à
2. Connect the red clamp to the positive (+) terminal of the battery.
3. Connect the black clamp to the negative (-) terminal of the battery.
4. Wiggle the clamps back and forth to ensure proper connection.
5. Connect the power adaptor to the power supply.
Charging will start upon connection.
à
6.2 Disconnecting the cables
Important:
Never disconnect charger from battery by pulling the cables.
When finished using the product:
1. Disconnect the power adaptor from the power supply.
2. Disconnect the black clamp.
3. Disconnect the red clamp.
6.3 Barrel plug adaptor
The barrel plug adaptor can be used when needed to recharge built in led acid re-
chargeable batteries (e.g., kids electric ride-on toy vehicles).
Before using, check to make sure the specifications of the charger match the product.
See
Technical data
[} 4].
7 Status indicator light
Colour
Description
Red ON
Battery is charging
Red flashing
Battery is fully charged
Red OFF
The product has been operating for more than 12 hrs and
the timer protection function has triggered.
Short circuit or reverse polarity protection triggered. Check
for short circuits or if the output cables are connected to
correct battery poles. See:
8 Cleaning
Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
1. Disconnect from the power supply and battery. See:
2. Let the product cool down to ambient temperature.
4
Barrel plug adaptor
[} 4].
Connecting the cables
[} 4].
Disconnecting the cables
[} 4].
3. Clean the product with a dry, fibre-free cloth.
9 Disposal
This symbol must appear on any electrical and electronic equipment placed on
the EU market. This symbol indicates that this device should not be disposed of
as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-
back of waste. Conrad provides the following return options free of charge (more details on
our website):
in our Conrad offices
at the Conrad collection points
at the collection points of public waste management authorities or the collection points
set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply
in countries outside of Germany.
10 Technical data
Input ............................................... 100 - 240 V/AC, 50 - 60 Hz, 18 W
Outputs........................................... 6 V/DC: 800 mA
Supported battery types ................. 6 V/DC, 12 V/DC, lead acid
Termination voltage........................ 6 V: 7.2 V
Barrel plug adaptor......................... ø2.5 mm (inner) / ø5.5 mm (outer) barrel plug
Protection mechanisms .................. Short circuit, reverse polarity, timer (12 hrs)
Protection class .............................. II
Operating conditions....................... 10 to +55 °C, 10 - 90 % RH (non-condensing)
Storage conditions.......................... 0 to +55 °C, 5 - 95 % RH (non-condensing)
Output cables ................................. 1.2 m
Dimensions (L x W x H).................. 74.3 x 28.6 x 78.7 mm
Product weight................................ Charger: 107.4 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2867717_V3_1123_dh_mh_en 18014399448616715-2 I3/O3 en
12 V/DC: 800 mA
12 V: 14.6 V
Cable: 48.6 g

Publicité

loading

Ce manuel est également adapté pour:

2867717