Chicco Oasys 2-3 Mode D'emploi page 34

check that the diagonal belt loop (B) is posi-
tioned at a maximum of 2 cm above the child's
shoulder (Diag. 16)
To make the adjustment:
1. Use one hand to press the child car seat
backrest height adjuster lever (L) located on
the back of the headrest (Diag. 17)
2. Raise/lower the backrest to adapt it to the
height of the child's shoulders (Diag. 18)
3. Release the lever checking that it has clicked
into the desired position.
Adjusting the width of the back rest
The width of the backrest can be adjusted to
adapt the child car seat to suit the physique
of the child.
Use the backrest width regulator wheel (K) lo-
cated above the headrest, to adjust the width:
1. Rotating it counter clockwise will increase
the width of the backrest (Diag. 19) while
rotating it clockwise will decrease the width
(Diag. 20).
Adjusting the inclination of the child car
seat backrest/seat
It is possible to recline the child car seat by us-
ing the reclining adjuster button (H).
The child car seat backrest/seat can be re-
clined to 4 different positions to allow the
child to travel in absolute comfort.
To recline the backrest simply grasp hold of
the front section of the seat (Diag. 21) and pull
it towards you.
Simply press the reclining adjuster button
(H) pushing the seat backwards towards the
vehicle seat backrest to return it to a vertical
position.
WARNING! never recline the child car seat
when in use. Before adjusting the backrest,
remove the child from the child car seat.
After reclining or straightening the Oasys child
car seat, always check that the car 3-point
safety belt is suffi ciently taut and a maximum
of 2 cm above the shoulder of the child (Diag.
16).
Always perform the above operations when
the vehicle is at a standstill.
Removable backrest/seat covers
The child car seat fabric cover is completely
removable and washable. It is attached to
the structure using velcro straps and elastics
(Diag. 22)
Straighten the backrest (C) upright and widen
the side fl aps (N).
Backrest
Start from the lower section of the side fl aps,
separate the fabric lining from the Velcro fas-
teners (diag. 23) and lift it off.
Now separate the central section of the
backrest working from the bottom upwards,
removing the entire cover, including the head-
rest section, undoing any elastic fasteners
found behind the backrest. (Diag. 24)
Seat
1. Open the velcro fastener on the back of the
seat (Diag. 25).
2. Pull the fabric cover so the elastic is taut,
then remove it from the lap belt loop (F) on
both sides (Diag. 26)
3. Grasping both elastics, remove this section
of the fabric cover from the lap belt loops
(F) on both sides (Diag. 27)
4. The central protection is fastened to the
backrest by two toothed fi xtures, pull the
central protection upwards, releasing the
toothed fi xtures from their seats (Diag. 28).
5. Pull the cover up over the armrests and re-
move.
6. Now fi nish the removal process by pulling
the triangular plastic reinforcement, fi tted
around the reclining adjuster button (H),
upwards (Diag. 29 A and 29 B).
To replace the cover on the frame:
Straighten the backrest upright and widen the
side fl aps.
Seat
Start by covering the seat, repeating opera-
tions 6 to 1 in the reverse order, paying partic-
ular attention that the cover fi ts over all parts
of the frame perfectly, especially around the
two lap belt guides (F) threading the elastics
under each of them.
34