Publicité
Liens rapides
Operator's manual
KL1400XT
Electric Pressure Washer
N120-0049-rev3
2023/07/12
Convenient and simple
accessories storage
Rear hose reel aligns
with pump output coupler
Large wheels - easy to
maneuver
Easier lifting leverage with
centered rear lifting handle
Thermal Protector
Total Stop
Easy Start
Publicité
Manuels Connexes pour MSG KL1400XT
Sommaire des Matières pour MSG KL1400XT
- Page 1 Operator’s manual KL1400XT Electric Pressure Washer N120-0049-rev3 2023/07/12 Convenient and simple accessories storage Rear hose reel aligns with pump output coupler Large wheels - easy to maneuver Easier lifting leverage with centered rear lifting handle Thermal Protector Total Stop Easy Start...
- Page 2 Table of contents Table of contents Introduction Using the operators manual ..............3 Product Identifi cation ................3 Product serial number and registration ...........3 Identifi cation of components ..............4 Component checklist ................4 Safety Description of warnings ................5 Description of safety symbols ..............5 Description of Hazard Warnings ...............5 Product labels/ Warning labels ...............
- Page 3 Introduction Congratulations on the purchase of your new MS GREGSON KL1400XT electric cold water pressure washer. This product has been carefully designed and manufactured to provide the highest level of quality, safety, endurance and opti- mal performance. Each component has been thoroughly and diligently tested to ensure precise peak performance.
- Page 4 Introduction - Components Transport handle Storage compartment soap bottle High pressure hose Main power switches Storage compartment nozzles Hose quick twist connector water outlet Lifting handle Spray gun Hose twist connect for spray gun Warning decals Screen filter ring Spray gun trigger Storage brackets spray gun, wand, brush Fitting pump inlet 3/4’’...
- Page 5 Safety - Description of warnings The «DANGER» symbol is used to outline a situation where danger is DANGER imminent and must be strictly avoided. Failure to comply could result in serious injury or even death. The« Warning» symbol describes the potential for danger or improper WARNING set up and that should be avoided.
- Page 6 Safety - Warning labels Caution label indicates to NEVER aim Warning label reminds users to spray gun at people, animals, electrical read the instruction manual care- outlets or the pressure washer. fully before using the machine. Identifi cation label contains model/ serial number and technical infor- mation for the pressure washer.
- Page 7 Safety - Precautions / Protective gear / Electrical shock WARNING Risk of eye injury. High pressure spray can propel loose stones or objects at high velocity. • Always wear safety goggles and protective clothing when using this equipment or in vicinity of where equipment is in use. •...
- Page 8 Safety – Precautions hot surfaces / Important notices WARNING • Certain motor and pump components get hot during extented operation. Contact with hot surfaces can burn skin. WARNING Avoid freezing. At 32°F (0°C), the machine can freeze. 32ºF 0ºC • Freezing temperature can cause serious damage to the pump if not winterized.
- Page 9 Safety – Precautions high pressure stream / Slippery surfaces WARNING High velocity spray fluids can penetrate skin, causing serious injury. In the event that an accident occurs and spray appears to have penetrated the skin, SEEK EMERGENCY MEDICAL ATTENTION. DO NOT treat water penetration into the skin as a simple cut.
- Page 10 Assembly instructions - Components Installing top carry handle • Carry handle facilitates easy rolling when moving the pressure washer. • Secure the handle with using 2 screws included in the box. • Ensure the handle is fi rmly inserted into the pressure washer body (the front surfaces should be aligned with screws holes ).
- Page 11 Assembly instructions - Components Inserting bayonet mount nozzles. Depending on the job to be done, fi t one of the two nozzle types, by inserting it into the lance extension. Inserting nozzle • Align slots on wand connector with nozzle. •...
- Page 12 Operating instructions - Connecting water / Electrical power Connecting Main Water Supply 1. Connect high pressure hose to the pump output outlet (1). of the pressure washer. 2. Ensure twist coupler (2) is fi rmly tightened. 3. Use quick twist connect 3/4" MGT water inlet hose fitting coupler to attach garden hose to water inlet on pump (3) 4.
- Page 13 Operating instructions - Safety features and devices Thermal protector stops the operation of the pressure washer in the event the electrical motor is overheating. IF THE MACHINE IS STOPPED BY THERMAL PROTECTOR: • Main power switch should be put to the OFF «0» position. Then remove the plug from the power outlet. •...
- Page 14 Operating instructions - Safety features and devices Pressure limit/adjustment valve This valve has been correctly set at the factory and enables the pumped fluid to return to the pump’s suction unit, preventing and limiting dangerous levels of pressure when the spray gun is stopped. CAUTION Proper pressure levels must be set by an authorized service technician.
- Page 15 Operating instructions - Start up procedure Steps to Getting Started 1. Ensure main power switch is OFF («0» position). 2. Insert electrical plug into the power outlet. 3. Unroll and attach the high pressure hose to the pressure washer pump. 4.
- Page 16 Operating Instructions - Switching off and Storage Switching Off 1. Close the tap from water supply securely and disconnect the water supply hose from the pressure washer. 2. Empty water from pressure washer by squeezing spray gun trigger while the motor is run for a few seconds to eliminate remaining pressure from high pressure hose.
- Page 17 Operating instructions / Special Maintenance Special Maintenance intervals MAINTENANCE ACTION WARNING INTERVALS • Specialized maintenance procedures should Every 50 hours • Check the pump hydraulic circuit. only be carried out by an authorized service • Check the pump fi ttings. technician.
- Page 18 Technical specifi cations ELECTRICAL CONNECTION Main power supply 115 V • 60 Hz Amperage 13.5 A Absorbed power 1.5 kW Fuse 15 A HYDRAULIC CONNECTION Maximum inlet water temperature 40°C • 98°F Minimum inlet water temperature 5°C • 41°F Maximum inlet water flow 8.5 l/min •...
- Page 19 Exploded views / Parts list Ref. Part no. Pièces English description Description française Quan. CO-455/13 Nozzle cleaning pin Tige de nettoyage de buse CO-3217/208 Adjustable nozzle Buse ajustable CO-3301/1042 Wand Lance CO-3217/203 Rotating nozzle Buse rotative CO-3301/1076 Foamer Mousseur CO-2410/83 Spray gun Pistolet CO-1413/45...
- Page 20 Exploded views / Parts list KL1400XT Nettoyeur à pression électrique Electric pressure washe English description Description française Quan. Ref. Part No.Pièces CO-402/305 Handle cover Couvercle de la poignée CO-1411/32 Handle Poignée CO-3605/114 Screw CO-477/217 Left cover Couvercle gauche CO-602/64 Hose reel disc Disque de l’enrouleur...
- Page 21 Product warranty Pressure washers manufactured by or for MS GREGSON are warranted, to the original purchaser, to be free from defects in mate- rials and workmanship for the periods specifi ed below. Normal use conditions, according to the instructions in this manual, apply. This limited warranty is subject to the exclusions listed below, is calculated from the date of delivery to the original purchaser, and applies to the original components only.
- Page 22 MS Gregson Inc. 4300, Vachon st. Drummondville (Qc) Canada J2B 6V4 Tel.: 819 474-1910 Fax: 819 474-5317 info@msgregson.com www.msgregson.com...