Colour-Wheel; Effect-Wheel; Shutter; Dimmer / Washlight - Futurelight CC-200 Color changer Mode D'emploi

2. Press the [Mode] key in order to access the main menu. Browse through the menu by pressing the [Up]
and
[Down] keys until the display shows "LAMP". Confirm by pressing [Enter] key.
3. Use the [Up] and [Down] keys to select "On" for switching on the lamp and "Off" for switch off the lamp
and press [Enter] to confirm or [Mode] to cancel.
Note :
It is also important to note that the discharge lamp is a cold restrike type, which means that it has to be cold
before re-striking. For this reason, you have to wait 5 minutes (max. speed of fan must be adjusted) after
having switched off the lamp before you can switch it back on again. If you try to switch on the lamp within 5
minutes after having switched it off, the CC-200 will store this information and automatically ignite the lamp
when the 5 minutes period has expired. The message "HEAt" will appear on the control board display at the
back side of the CC-200. If the ignition of the lamp is seven times unsuccessful, on the display will appear
"LA.Er", meaning that the lamp could be damaged or even missed, or there could be a failure on the ignitor
or ballast.

6.3 Colour-wheel

The CC-200 features a colour-wheel with 12 color positions - 11 of these with dichroic colors and the last one
open. The wheel can be positioned between two adjacent colors in any position. It is also possible to rotate
the color-wheel continuously at different speeds - the so-called "Rainbow effect" is created.

6.4 Effect-wheel

This wheel has both hot and cold color temperature filters (3200 K and 5600 K), UV filter for wood light.
Cyan, Magenta and yellow filters for color mixing with color wheel allowing another 36 colors. Two
replaceable gobos and three beam reducers. The gobos have an outside diameter of 27 mm and an image
diameter of 23 mm.

6.5 Shutter

The shutter unit enables to produce strobo effect from 1 to 8 flashes per seconds.

6.6 Dimmer / Washlight

0 - 100 % smooth dimming to sharp beam or „wash" light is provided by the special dimmer unit.

6.7 Fan

The CC-200 is cooled by one axial fan. The speed of the fan (and of course the noise) can be continuously
reduced if very quiet performance is required.
By the Control Board using the "FAnS" function you can choose 4 types of low fan speed operating:
1. "HIGH" - high speed of the fans
The cooling fans work on max. speed (max. cooling).
2. "reG" - continuous controlling of the fan speed
The fan automatically raises its speed in order to control inside temperature of the lighting, if the
temperature inside increases about certain level (the low fan speed reduces the cooling of the lighting).
This cycle can repeat several times until the temperature inside is on suitable level.
3. "Lo.OF" - low speed / Switch off the lamp
The fan keeps the adjusted low speed until the temperature exceeds max. inside temp. then the CC-200
automatically switches off the lamp.
4. "Lo.HI"- low/high speed of the fan operating
The fan keeps the adjusted low speed until the temperature exceeds max. inside temp. of the fixture, then
the CC-200 automatically switches from low to high the fan speed.
The Control Board situated on the top side of the CC-200 offers several features. You can simply set the
lighting address, read the number of lamp or unit hours, switch on and off the lamp, run test show, make a
reset and also use special functions for manual control and service purposes.
The main menu is accessed by pressing the [Mode] key - press this one so many times until the display
shows message "A001" (with actually stored address). Browse through the menu by the pressing [Up] and
[Down] keys - the display shows step by step these messages: A001, Lati, Poti, LAMP, tESt, rESE, SPEC.
Press [Enter] if you wish to select one of them. The functions provided are described in the following

7. Control Board

32