Saf-Fro SAXO 1500 Instruction De Securite D'emploi Et D'entretien page 3

GB
1.0 TECHNICAL DESCRIPTION
1.1 DESCRIPTION
The system consists of a modern direct current generator for the welding of
metals, developed via application of the inverter. This special technology allows
for the construction of compact light weight generators with high performance.
l'ts adjust ability, effeciency and energy consumption make it an excellent work
tool suitable for coated electrode and GTAW (TIG) welding.
1.2 TECHNICAL SPECIFICATIONS
DATA PLATE
Single phase supply
Frequency
Effective consuption
Maximum consuption
Open circuit voltage
Welding current
Duty cycle 25%
Duty cycle 60%
Duty cycle100%
Protection class
Insulation class
Weight
Dimensions
European Standards
1.3 DUTY CYCLE AND OVERHEATING
Duty cycle is the percentage of 10 minutes at 40°C ambient temperature that the
unit can weld at its rated output without overheating. If the unit overheats, the
output stops and the over temperature light comes On. To correct the situation,
wait fifteen minutes for unit to cool. Reduce amperage, voltage or duty cycle
before starting to weld again (See page III).
1.4 VOLT - AMPERE CURVES
Volt-ampere curves show the maximum voltage and amperage output capabilities
of the welding power source. Curves of other settings fall under curves shown
(See page III).
2.0 INSTALLATION
IMPORTANT: Before connecting, preparing or using equipment,
read SAFETY PRECAUTIONS.
2.1 CONNECTING THE POWER SOURCE TO THE MAINS ELECTRICITY
SUPPLY.
Serious damage to the equipment may result if the power source is
switched off during welding operations.
Check that the power socket is equipped with the fuse indicated in the features
label on the power source. All power source models are designed to compensate
power supply variations. For variations of +-10%, a welding current variation of +-
0.2% is created.
PRIMARY
230 V
50 Hz / 60 Hz
16 A
31 A
SECONDARY
85 V
5 A ÷ 150 A
150 A
120 A
100 A
IP 23
H
Kg. 7
mm 145 x 230 x 365
EN 60974.1 / EN 60974.10
BEFORE INSERTING THE MAINS PLUG, IN
ORDER TO AVOID THE FAIL OF POWER
SOURCE, CHECK IF THE MAINS CORRE-
SPONDS TO THE WISHED MAIN SUPPLY.
TECHNICAL DESCRIPTION
ON - OFF SWITCH:
This switch has two positions: I and 0.
2.2 HANDLING AND TRANSPORTING THE POWER SOURCE
OPERATOR SAFETY:
Welder's helmet - Glowes - Shoes with high insteps.
The welding power source do not weight more than 25 Kg and
can be handled by the operator. Read well the following precautions.
The machine is easy to lift, transport and handle, though the following procedures
must always be observed:
1. The operations mentioned above can be operated by the handle on the
power source.
2. Always disconnect the power source and accessories from main supply
before lifting or handling operations.
3. Do not drag, pull or lift equipment by the cables.
2.3 SELECTING A LOCATION
Special installation may be required where gasoline or volatile
liquids are present. When locating equipment, ensure that the following guide-
lines are followed:
1. The operator must have unobstructed access to controls and equipment
connections.
2. Use rating plate to determine input power needs.
3. Do not position equipment in confined, closed places. Ventilation of the
power source is extremely important. Avoid dusty or dirty locations, where
dust or other objects could be aspirated by the system.
4. Equipment (Including connecting leads) must not obstruct corridors or
work activities of other personnel.
5. Position the power source securely to avoid falling or overturning. Bear in
mind the risk of falling of equipment situated in overhead positions.
2.4 CONNECTION AND PREPARATION OF EQUIPMENT FOR STICK WELDING.
• TURN OFF WELDER BEFORE MAKING CONNECTIONS.
Connect all welding accessories securely to prevent power loss. Carefully fol-
low safety regulations described in SAFETY RULES.
1. Fit the selected electrode to the electrode clamp.
2. Connect the earth lead connector to the negative (-) quick-connection termi-
nal Ref. 6 - Fig. 1 page 3) and the earth clamp of the workpiece near the
welding zone.
3. Connect the electrode clamp connector to the positive (+) quick-connection
terminal Ref. 5 - Fig. 1 page 3) .
4. CAUTION: Make the above connection for direct polarity welding; for
inverse polarity, invert the connection: earth lead CONNECTOR to the
quick-connection positive (+) terminal and the electrode holder clamp
connector to the negative (-) terminal.
5. Adjust welding current with ampere selector Ref. 2 - Fig. 1 page 3) .
6. Press the illuminated switch to turn on the power source Ref. 1 - Fig. 1
page 3) .
N.B. Serious damage to the equipment may result if the power source is
switched off during welding operations.
The power source is fitted with an anti-sticking device that disables power if
output short circuiting occurs or if the electrode sticks, allowing it to be easily
detached from the workpiece.
This device enters into operation when power is supplied to the generator, even
during the initial checking period, therefore any load input or short circuit that
occurs during this phase is treated as a fault and will cause the output power to be
disabled.
(GB) 2
GB