Publicité
Les langues disponibles
Les langues disponibles
11
ITEM(S) NEEDED
#8 x 1
ab. The other Splicer and Shrink Tube should be added to
the Plug Receptacle so it can be attached to the Boat
Wires. Take the Plug Receptacle (Item #B) and place
one Shrink Tube (Item #6), followed by one Splicer
(Item #8) on the end of the black Negative (-) Wire of
the Plug Receptacle. Secure the Splicer by tightening
the Set Screw with a 3/32" Allen Wrench (Item #14) to
20 in-lbs.
ac. Take the Plug Assembly and identify the red Positive
(+) Power Lead on the Plug Assembly and align
it with the Positive (+) Power Lead on the Trolling
Motor Wires. Insert it into the Splicer at the end of
the Positive (+) Lead Wire from the Plug Assembly.
Take the black Negative (-) Power Lead from the Plug
Assembly and align it with the Negative (-) Power Lead
from the Trolling Motor Wires. Insert it in the Splicer at
the end of the black Negative (-) Power Lead of from
the Trolling Motor Wires. Secure the Set Screw of both
Splicers with the 3/32" Allen Wrench.
12
ad. Once the Splicers are secure on both wires, take the
Shrink Tubes and slide them over the Splicers. The
Shrink Tubes should be centered over the Splicers and
completely cover the wire connections.
The Shrink Tubes are meant to water
NOTICE:
proof the connection between the Plug Assembly
and the Trolling Motor Wires. Make sure there are
no gaps around the wires that would allow water to
reach the connection.
ae. When satisfied with the position, secure the Shrink
Tubes in place with a Heat Gun. Then slide the Splice
Cover over the Shrink Tubes to complete
the installation.
When disconnecting the Plug Assembly
NOTICE:
from the Receptacle, be sure to install and tighten the
Dust Cap. This will prevent water or debris intrusion.
For warranty information, please visit minnkotamotors.com.
minnkotamotors.com
Part #2377182
#6 x 1
#14 x 1
11ab
11ad
Minn Kota Consumer & Technical Service
Johnson Outdoors Marine Electronics, Inc.
PO Box 8129
Mankato, MN 56001
ECN 42520
Plug
Plug
Assembly
Assembly
Negative Power
Negative Power
Lead (-)
Lead (-)
Positive Power
Positive Power
Lead (+)
Lead (+)
Shrink Tube
Shrink Tube
Splicer
Splicer
Plug Assembly
Plug Assembly
Shrink Tube
Shrink Tube
When connecting the Plug Assembly to the
NOTICE:
Receptacle, be sure to tighten the Threaded Collar
to ensure a proper water-tight seal. A water-tight seal
protects electrical contacts. Failure to tighten the
Threaded Collar could result in water intrusion.
121 Power Drive
Mankato, MN 56001
Phone (800) 227-6433
Fax (800) 527-4464
11ac
Plug
Plug
Assembly
Assembly
Negative (-)
Negative (-)
Power Lead
Power Lead
Positive (+)
Positive (+)
Power Lead
Power Lead
Shrink
Shrink
Tube
Tube
Splicer
Splicer
Splicer
Splicer
Shrink
Shrink
Tube
Tube
Negative (-)
Negative (-)
Power Lead
Power Lead
Positive (+)
Positive (+)
Power Lead
Power Lead
Trolling
Trolling
Motor Wires
Motor Wires
11ae
Threaded
Threaded
Collar
Collar
Plug Assembly
Plug Assembly
Splice Cover
Splice Cover
©2022 Johnson Outdoors Marine Electronics, Inc.
All rights reserved.
Rev A
05/22
Publicité
