Scheppach WOODSTAR sl 10 lu Traduction Du Manuel D'origine page 23

reduced noise development, insofar as possible.
Maintain the electric tool and tool attachments
regularly and if necessary, initiate repairs in
order to reduce noise.
– Report faults on the electric tool, protective
devices or the tool attachment to the person
responsible for safety as soon as they are dis-
covered.
3 Safe work
– Only use saw blades for which the maximum
permissible speed is not lower than the maxi-
mum spindle speed of the machine and which
are suitable for the material to be cut.
– Make sure that the saw blade does not touch
the rotary table in any position by pulling out the
mains plug and rotating the saw blade by hand
in the 45° and 90° position. If necessary, read-
just the saw head.
– When transporting the electric tool, only use
the transport devices. Never use the protective
devices for handling or transport.
– Make sure that the lower part of the saw blade is cov-
ered during transport, e.g. by the protective device.
– Be sure to only use spacers and spindle rings
specified by the manufacturer as suitable for the
intended purpose.
– The floor around the machine must be level,
clean and free of loose particles, such as chips
and cutting residues.
– Do not remove any cutting residues or other
parts of workpieces from the cutting zone while
the machine is running and the saw unit is not
at rest.
– Make sure that the machine is always secured
on a workbench or a table if at all possible.
– Support long workpieces (e.g. with a roller table)
to prevent them sagging at the end of a cut.
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair active
or passive medical implants under certain conditions. In
order to prevent the risk of serious or deadly injuries, we
recommend that persons with medical implants consult
with their physician and the manufacturer of the medical
implant prior to operating the electric tool.
SAFETY INSTRUCTIONS FOR THE HANDLING OF
SAW BLADES
1 Only use insertion tools if you have mastered their
use.
2 Observe the maximum speed. The maximum
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.
Observe the motor / saw blade direction of rotation.
3
4 Do not use any insertion tools with cracks. Sort out
cracked insertion tools. Repairs are not permitted.
5 Clean grease, oil and water off of the clamping
surfaces.
Do not use any loose reducing rings or bushes for
6
the reducing of holes on saw blades.
7 Make sure that fixed reducer rings for securing the
insertion tool have the same diameter and have at
least 1/3 of the cutting diameter.
8 Make sure that fixed reducer rings are parallel to
each other.
9 Handle insertion tool with caution. They are ideally
stored in the originally package or special contain-
ers. Wear protective gloves in order to improve
grip and to further reduce the risk of injury.
10 Prior to the use of insertion tools, make sure that
all protective devices are properly fastened.
11 Prior to use, make sure that the insertion tool
meets the technical requirements of this electric
tool and is properly fastened.
12 Only use the supplied saw blade for cutting wood,
never for the processing of metals.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
0
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with unpro-
tected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure
to the beam can occur.
• If the mitre saw is not used for an extended period
of time, the batteries should be removed.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.
Safety instructions for handling batteries
Always make sure that the batteries are inserted
1
with the correct polarity (+ and –), as indicated on
the battery.
2 Do not short-circuit batteries.
3 Do not charge non-rechargeable batteries.
4 Do not overcharge batteries!
5 Do not mix old and new batteries or batteries of
different types or manufacturers! Replace an entire
set of batteries at the same time.
Immediately remove used batteries from the de-
6
vice and dispose of them properly! Do not dispose
batteries with household waste. Defective or used
batteries must be recycled according to Directive
2006/66 / EC. Give back batteries and / or the device
has been offered to the collective facilities. About
disposal facilities you can inform by your municipal
or city government.
7 Do not allow batteries to heat up!
GB/IE 23