Fan Control - PLYMOVENT ControlPro Manuel D'installation

WaRNiNg
- Shorten excessive cable lengths. A coil or bundle
of cables can cause electromagnetic interference.
- Make sure that you connect the wiring in the
correct way. Wrong wiring may cause permanent
damage to the PC board.
- Use cable glands to insert cables into the Panel.
- Keep the blanking plugs on the cable glands that
are not in use to avoid pollution of the Panel.
- For all connections, also refer to the separately
supplied electrical diagram.
- Refer to Table II on page 85 for a specification
of the digital inputs (high/low).
general instructions to connect a cable to a
certain connector (unless otherwise stated)
Wire stripping:
A
B
• (1) Put the cable through a cable gland M16 into the
Panel.
• (2) Carefully remove the connector from the PC board.
Pull the connector in a horizontal direction.
• Cut the cable to the correct length and strip the wires.
Fan Pressure
sensor
Filter Pressure
sensor
1
Shielded cables only:
Fan Pressure
• Put a shrink tube on the drain wire (A) and the cable
sensor
jacket (B).
1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12
• Use a heat gun (C) to tighten the shrink tube.
4
A B
B
Filter Pressure
sensor
1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
3
1
All cables:
IN 5
• (3) Put the wires into the connector.
• (4) Tighten the screws. IN 6
• (5) Put the connector back on the PC board.
IN 7
• Tighten the cable gland.
IN 8
4
3
Detachable screw terminal block ("connector")
0000112606/200917/0 ControlPro
a
B
Digital input 1-5
Digital input 6-12
Digital input 1-5
Digital input 6-12
External start/stop signal
2
Fire alarm (ShieldControl)
Sliding valve feedback 1
Sliding valve feedback 2
4.4.1
To install the mains cord, do the following.
Fig. 4.9
• Put the mains cord (B) through the metal cable gland
into the Panel.
• Connect the mains cable to the terminal block (A).
• Tighten the cable gland.
A
B
mm in.
C
50 2
6 ¼
Fig. 4.9
4.4.2
RS485 VFD CAN Slave
CAN HMI
2
RS485 VFD CAN Slave
1 2 3 4 5 1 2 3 4 5
Power
C
C
5
CAN HMI
1 2 3 4 5
Fig. 4.10 Connection Panel  HMI
IN 9 Fan alarm
IN 10 Compressed air switch
IN 11 External alert 4.4.3
IN 12 Dustbin level switch
Depending on the selected fan control equipment, you can
connect the fan in two different ways:
- Plymovent VFD/Panel (frequency inverter) by RS-485 cable
5
- direct fan start by conventional cables
Connect the selected fan control equipment in accordance with
the instructions below.
17. Size M20
Mains cord (cable #5)
cautioN
High voltage connection
Filter pressure
-
(internal sensor)
+
Fan pressure
-
(internal sensor)
+
RS-232
(for service only)
Mains cord
Panel  HMI
Dustbin Fan Pressure
Valves Indicator LED's
sensor sensor
Analog
Filter Pressure
Light tower
sensor
output
Wiring colours
+24V red
CAN_H white
CAN_L blue
GND black
SHD drain wire (with
shrink tube)

Fan control

(C)
17
CAN Slave
Digital input 1-5 RS485 VFD
Digital input 6-12 CAN HMI
cable #1
[page 8]
EN - 8