PLYMOVENT ControlPro Manuel D'installation page 14

For connection of the internal pressure sensors,
refer to paragraph 4.5.
You must use external pressure sensors
internal ones when:
- the distance between the Panel and the filter system MDB or
SCS / EDS is more than 10 m; and/or
- the Panel is installed outdoor and the temperature may drop
below 0°C (32°F)
In all other cases the use of external pressure sensors is
Fan Pressure
optional.
Digital input 1-5
sensor
NO 1 1
Filter Pressure
sensor
NC 1 2
COM 1 3
4
NO 2 5
NC 2 6
Fan Pressure
COM 2 7
sensor Dustbin
Valves Indicator LED's
8 sensor
8
1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12
Analog
Power Light tower
output
Fan Pressure
Digital input 1-5
sensor
Filter Pressure
sensor
1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Filter Pressure
sensor
IN 5 External start/stop signal
IN 6 Fire alarm (ShieldControl) Power
Fan Pressure
IN 7 Sliding valve feedback 1
sensor
IN 8 Sliding valve feedback 2
1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12
Fig. 4.25 Connection of external pressure sensor(s)
Filter Pressure
sensor
1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
4.4.12 Dustbin level detection
There are two types of dustbin level indicators:
- dustbin level switch, that shows the dustbin to be full or
empty
Power
- dustbin level sensor, that shows the percentage of filling
IN 5 External start/stop signal
1 2
IN 6 Fire alarm (ShieldControl)
In case of a dustbin level switch
IN 7 Sliding valve feedback 1
IN 8 Sliding valve feedback 2
Additional instruction:
• Connect the dustbin level switch as NO (normally open)
28. Type PT-1000 or PT-2500
29. Future development
30. NO means that the dustbin is empty
0000112606/200917/0 ControlPro
instead of the
28
Digital input 6-12
Digital input 1-5
Fan Pressure
Digital input 1-5 RS485 VFD
sensor
Filter Pressure
Digital input 6-12
sensor
cable #13
Digital input 6-12
Digital input 6-12
Valves
cable #14
IN 9
IN 10 Compressed air switch
Digital input 1-5
IN 11 External alert
IN 12 Dustbin level switch
Valves
Digital input 6-12
1 2 3 4 5 6 1 2 3 4 5 6 7
(option)
29
IN 9
1 2 3 4 5 6 7
IN 10 Compressed air switch
IN 11 External alert
IN 12 Dustbin level switch
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
-
+
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
-
+
Valves
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
-
Power
RS485 VFD CAN Slave
+
CAN HMI
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
RS485 VFD CAN Slave
Fig. 4.26 Connection of dustbin level switch
CAN Slave
1 2 3 4 5 1 2 3 4 5
CAN HMI
In case of a dustbin level sensor
RS485 VFD CAN Slave
CAN HMI
1 2 3 4 5
CAN HMI
Dustbin
Indicator LED's
sensor
[page 8]
Fan alarm
Analog
Valves
Light tower
output
RS485 VFD CAN Slave
Power
1 2 3 4 5 1 2 3 4 5
[page 8]
Dustbin
Indicator LED's
sensor
CAN HMI
1 2 3 4
1 2 3 4 5
Fig. 4.27 Connection of dustbin level sensor
Analog
Light tower
output
Fan alarm
1 2 3
4.4.13 SHIELD fire safety solutions
ControlPro is SHIELD-ready. You must connect the following
components to the Panel (refer to paragraph 1.3.2):
.
30
- ShieldControl fire detection panel
IN 1 BTN start/stop fan
- sliding valves
IN 2 BTN lter cleaning
- 3/2 solenoid valve
IN 3 Service mode switch
IN 4 Spare
ShieldControl panel
ShieldControl is the fire detection panel of SHIELD fire safety
solutions.
Connection/functionality:
- to send a fire alarm signal from the ShieldControl panel to
the ControlPro
31. Only in combination with the MDB; not suitable for the SCS and EDS
Fan pressure
(internal sensor)
Digital input 6-12
RS-232
(for service only)
Filter pressure
(internal sensor)
Digital input 6-12
Dustbin Fan Pressure
Indicator LED's Digital input 1-5
sensor sensor
Fan pressure
Analog
Filter Pressure
Light tower Digital input 6-12
(internal sensor)
sensor
output
Digital input 6-12
RS-232
(for service only)
Fan Pressure
Digital input 1-5
sensor
Filter Pressure
Dustbin Fan Pressure
Indicator LED's Digital input 1-5
sensor sensor
sensor
Analog
Filter Pressure
Digital input 6-12
Light tower
output sensor
Fan Pressure
Digital input 1-5
sensor
1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12
Filter Pressure
sensor
1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
31
IN 5 External start/stop signal
IN 6 Fire alarm (ShieldControl)
IN 7 Sliding valve feedback 1
IN 8 Sliding valve feedback 2
RS485 VFD CAN Slave
CAN HMI
cable #12
[page 8]
input IN 12
RS485 VFD CAN Slave
Digital input 6-12
CAN HMI
cable #16
1 2
[page 8]
Digital input 6-12
(option)
IN 9 Fan
IN 10 Com
IN 11 Exte
IN 12 Dus
EN - 13
1
RS4
RS4