PLYMOVENT ControlPro Manuel D'installation page 15

Additional instruction:
• Remove the wire bridge from input IN 6.
Digital input 1-5
1 2 3 4 5 6 7 8 9 10 11 12
Digital input 6-12
Digital input 1-5
Dustbin
Valves Indicator LED's
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 sensor
1 2 3 4 5 6 7 8 9 10 11 12
Analog
Power
Light tower
output
Digital input 6-12
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 6-12
Digital input 6-12
Sliding valves
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A SHIELD system contains two sliding valves
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
connected duct system, that open and close at the same time.
Connections/functionalities:
- output signal to open/close the sliding valves
- feedback signal when the sliding valves are closed
Digital input 6-12
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 1-5
1 2 3 4 5 6 7 8 9 10 11 12
Digital input 6-12
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 6-12
Dustbin
Valves Indicator LED's
sensor
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Analog
Power
Light tower
output
Digital input 6-12
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 6-12
Valves
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6
Digital input 6-12
Valves
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6
32. One before and one after the filter system
0000112606/200917/0 ControlPro
Digital input 6-12
Fan Pressure
RS485 VFD
Digital input 1-5
sensor
Filter Pressure
Digital input 6-12
sensor
cable #11
input IN 6
in the
32
Fan Pressure
RS485 VFD
Digital input 1-5
sensor
Filter Pressure
Digital input 6-12
sensor
cable #21
input IN 7
input IN 8
input OUT 1
3/2 solenoid valve
Valve to shut off the compressed air supply in case of fire in
the extraction/filter system. For enhanced safety it releases
the air from the filter's compressed air tank a the same time.
Connection/functionality:
Digital input 1-5 - output signal to shut off the compressed air supply and to
release the compressed air tank
1 2 3 4 5 6 7 8 9 10 11 12
Digital input 1-5
CAN Slave
1 2 3 4 5 6 7 8 9 10 11 12
CAN HMI
Valves
Valves
1 2 3 4 5 6
Power
[page 8]
Valves
Valves
1 2 3 4 5 6
1 2 3 4 5 6
Valves
4.5 pneumatic connection
1 2 3 4 5 6
Digital input 1-5
4.5.1 Filter pressure sensor
1 2 3 4 5 6 7 8 9 10 11 12
To monitor the filter pressure, you must connect pneumatic
hoses to the internal filter pressure sensor (+ and –).
Fig. 4.28
• Connect the pneumatic hoses + and – to the corresponding
bulkhead connectors (B).
• For connection of the pneumatic hoses to the MDB or SCS /
CAN Slave
EDS filter system, refer to the corresponding manual.
CAN HMI
4.5.2 Fan pressure sensor
To monitor the fan pressure
hose to the internal fan pressure sensor.
Valves
1 2 3 4 5 6
You can measure the fan pressure:
- before the filter system; or
- after the fan
[page 8]
This determines the connection of the hose.
Valves
pressure
measurement
1 2 3 4 5 6
before the filter system
after the fan
Fig. 4.28
• Determine the position of the pressure sensor in the
extraction duct (before the filter system or after the fan).
• Connect the pneumatic hose to the corresponding bulkhead
connector + or – (A).
33. In case of Plymovent VFD/Panel or other type of frequency inverter
Dustbin Fan Pressure
Indicator LED's
sensor sensor
Analog Filter Pressure
Light tower
output sensor
Also refer to paragraph 4.4.11.
, you must connect a pneumatic
33
pressure
underpressure
overpressure
CAN Slave
Digital input 1-5 RS485 VFD
Digital input 6-12 CAN HMI
cable #18
[page 8]
input OUT 2
connection
– (minus)
+ (plus)
EN - 14