PLYMOVENT ControlPro Manuel D'installation page 10

In case of:
Plymovent VFD/Panel (frequency inverter
NO 1 1
NC 1 2
COM 1 3
CAN Slave
RS485 VFD
4
NO 2 5
NC 2 6
COM 2 7
Valves Indicator LED's
CAN HMI
8
8
Power Light tower
RS485 VFD CAN Slave
1 2 3 4 5 1 2 3 4 5
Fig. 4.11 Connection of Plymovent VFD/Panel
CAN HMI
• Connect the other end of the cable to the frequency
Power
1 2 3 4 5
inverter:
- CAN-A to terminal 68
- CAN-B to terminal 69
- GND to terminal 61
• Make sure that switch S801 (BUS TER.) is set to 'on' to
enable termination on the RS-485 port.
IN 9 Fan alarm
IN 10 Compressed air switch
attENtioN
IN 11 External alert
To avoid earth loops, do not connect the shield of
IN 12 Dustbin level switch
the RS-485 cable to the frequency inverter.
For more information about the Plymovent VFD/
Panel, refer to the Danfoss documentation that is
supplied with the product.
Power
In case of:
1 2
Direct fan start
Types of control equipment for direct fan start:
- other type of frequency inverter (third party)
- star-delta switch
- other type of motor starter, e.g. Direct online (DOL)
Connections/functionalities:
- relay output (potential-free contact) for start/stop signal
- alarm input; high input triggers the "Fan alarm"
Valves Indicator LED's
Power Light tower
18. Danfoss
19. Max. 30V, 2,5A
0000112606/200917/0 ControlPro
RS-232
(for service only)
)
18
Dustbin Fan Pressure
Digital input 1-5
sensor sensor
Analog
Filter Pressure
Digital input 6-12
output sensor
(supplied with the VFD/Panel)
Valves
Valves
1 2 3 4 5 6 1 2 3 4 5 6 7
1 2 3 4 5 6 7
Dustbin Fan Pressure
Digital input 1-5
sensor sensor
Analog
Filter Pressure
Digital input 6-12
output sensor
( rmware updates)
Ethernet
(for service only)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
NO 1
NC 1
COM 1
NO 2
NC 2
COM 2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
RS485 VFD CAN Slave
Fig. 4.12 Connection of direct fan start
CAN HMI
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Additional functionality for frequency inverter:
- optional connection to the internal fan pressure sensor
cable #4
Dustbin
Indicator LED's
sensor
[page 8]
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Analog
Light tower
output
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Dustbin
Indicator LED's
sensor
1 2 3 4
Power
Analog
Light tower
output
1 2 3
Fig. 4.13 Connection to internal fan pressure sensor
IN 1 BTN start/stop fan
IN 2 BTN lter cleaning
IN 3 Service mode switch
19 IN 4 Spare
4.4.4
In case of an SCS / EDS:
• Proceed with paragraph 4.4.7
The SlaveBoard is integrated on the rear of each filter module
MDB-BM/2 and MDB-BM/4 (refer to Fig. II on page 82).
Cable #2 is supplied with a cable gland for connection to the
SlaveBoard box.
RS485 VFD CAN Slave
CAN HMI
20. Instead of an external pressure sensor (e.g. PT-1000 or PT-2500)
Digital input 6-12
1
2
3
4
5
6
Digital input 6-12
7
8 8
Digital input 6-12
attENtioN
Analogue output: 4-20 mA
Pressure range: 0-4000 Pa
Fan Pressure
Digital input 6-12
sensor
Power
Filter Pressure
sensor
Digital input 6-12
Fan Pressure
Dustbin Fan Pressure
sensor
Valves Indicator LED's
sensor sensor
1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12
Analog Filter Pressure
Light tower
output sensor
Power
1 2
Filter Pressure
sensor
1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
IN 5 External start/stop signal
IN 6 Fire alarm (ShieldControl)
IN 7 Sliding valve feedback 1
If you do not connect the frequency inverter to the
IN 8 Sliding valve feedback 2
internal fan pressure sensor, you must install and
connect an external pressure sensor (e.g. PT-1000
or PT-2500); refer to paragraph 4.4.11.
Panel  SlaveBoard (MDB only)
cable #19
[page 8]
input IN 9
20
Valves Indicator LED's
Digital input 1-5
Light tower
Digital input 6-12
Valves Indicator LED's
1 2 3 4 5 6 1 2 3 4 5 6
Digital input 1-5
Digital input 1-5 RS485 VFD CAN Slave
CAN HMI
Digital input 6-12
Light tower
1 2 3 4 5 6
cable #15
Digital input 6-12
[page 8]
IN 9
IN 10 Compr
IN 11 Extern
IN 12 Dustbi
EN - 9
1
1
RS485
RS485
1 2 3
Fan ala