PLYMOVENT ControlPro Manuel D'installation page 7

4.1.1 To be sourced locally
Mounting material :
9
- to install the Panel to the wall (hardware max. Ø 10 mm)
- to install the HMI to the wall (head height of screws max. 6
mm, Ø max. 4 mm)
Connection cables :
10
- refer to Table I on page 84 (#4 to 22) for the cable
specifications
If necessary:
- additional cable glands M16
Optional (for remote access to HMI via network):
- ethernet cable, min. CAT 5E shielded
4.2 Unpacking
Make sure that the product is complete. The package contains:
4.2.1 ControlPro/Panel
- Panel (control panel)
- double-bit key
- mounting bracket (4), incl. mounting material
- pneumatic hoses, incl. mounting material:
- 2x10 m (for filter pressure)
- 10+1 m (for fan pressure)
- installation manual
- electrical diagram
- UL compliance sticker
11
4.2.2 ControlPro/HMI
- HMI, incl. bracket and locking screw
- ethernet field connector (IP 67)
4.2.3 Connection cables
Fig. 4.1
A Panel  HMI cable, incl. heat shrinking tubes
B Panel  SlaveBoard cable
plug and heat shrinking tubes
C SlaveBoard  SlaveBoard cable
In case of a frequency inverter Plymovent VFD/Panel:
D RS-485 cable (to be ordered separately)
13
A [cable #1]
A
B
A
Fig. 4.1 Connection cables
9. The type of mounting material depends on the wall type
10. Number and type of cables depend on the selected options and control
equipment
11. For use in North America
12. MDB only
13. Included with EDS package; to be ordered separately for use with MDB and
SCS (due to variable length)
0000112606/200917/0 ControlPro
, incl. cable gland, termination
12
, incl. cable glands
12
B [cable #2] C [cable #3]
B
B
D [cable #4)
4.3 Mounting
You must install the Panel and HMI at a clearly visible and
accessible position.
4.3.1 ControlPro/Panel
To install the Panel, do the following.
Fig. 4.2
• Attach the mounting brackets (A) to the Panel with the
supplied mounting material (B).
• Install the Panel to the wall. Make sure that it is level.
Fig. 4.2 Mounting of the Panel
Fig. 4.3
North America only:
• To comply with UL standard 508A, put the corresponding
sticker on the Panel.
WARNING
Maintenance on Industrial Control
Panels shall only be performed by
trained, qualified,
authorized electricians,
appropriate safe electrical
practices including personal protective
equipment, approved tools, procedures
and accurate drawings of the panels
involved.
CAUTION
Risk of Electric shock
Disconnect Switch may be required to
de-energize before servicing.
AVERTISSEMENT
L'entretien des armoires industrielles
de contrôle doit
uniquement par des
qualifiées, expertes et autorisés en ce
sens utilisant des méthodes de travail
appropriées et sécurisées, y compris
les équipements de
individuelle, les outils, les procédures
approuvées et schémas électrique des
armoires en question.
ATTENTION
Risque de tension électrique
Il pourrait être nécessaire d'installer
un interrupteur principal pour mettre
hors-tension la machine
d'entreprendre les travaux d'entretien.
Fig. 4.3 UL compliance sticker
C
C The bottom plate contains the following cable glands and
C
connectors:
Fig. 4.4
A metal cable gland M20 for the mains cord
B universal cable glands M16 (8)
C bulkhead connectors (4) for the pressure tubes
14. Fan pressure + and – | Filter pressure + and –
attENtioN
Do not expose any component of ControlPro to
vibrations or heat radiation.
attENtioN
Before you install the Panel, make sure that the wall
is strong enough. Refer to paragraph 1.5.1 for the
weight.
A (4x)
skilled and
using
work
être effectué
personnes
protection
avant
B (4x)
14
EN - 6