Publicité
Les langues disponibles
Les langues disponibles
–
Use the upper blade guard and set it to the cor-
rect position.
Only use saw blades for which the maximum per-
–
missible speed is not lower than the maximum
spindle speed of table saws and which are suit-
able for the material to be cut.
–
Do not cut rebates or grooves without fitting a
suitable guard, e.g. a tunnel-type guard, over the
saw table.
Circular saws must not be used for slotting jobs
–
(cutting grooves which end in the workpiece).
When transporting the electric tool, only use the
–
transport devices. Never use the protective de-
vices for handling or transport.
Make sure that the upper part of the saw blade is
–
covered during transport, e.g. by the protective device.
Be sure to only use spacers and spindle rings
–
specified by the manufacturer as suitable for the
intended purpose.
–
The floor around the machine must be level, clean
and free of loose particles, such as chips and
cutting residues.
Always stand to the side of the saw blade when
–
working with the saw.
Do not remove any cutting residues or other parts
–
of workpieces from the cutting zone while the
machine is running and the saw unit is not at rest.
Make sure that the machine is always secured on
–
a workbench or a table if at all possible.
Support long workpieces (e.g. with a roller table)
–
to prevent them sagging at the end of a cut.
m Attention! Never remove loose splinters, chips
–
or jammed pieces of wood while the saw blade is
running.
•
Switch off the machine to troubleshoot or remove
jammed pieces of wood. - Disconnect the main
power plug -
•
Refitting, including adjusting and measuring
works, and cleaning must be carried out only
when the motor is switched off. - Disconnect the
main power plug -
•
Before switching on again, ensure that keys and
adjustment tools have been removed.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
Safety instructions for the handling of saw blades
1 Only use insertion tools if you have mastered
their use.
2 Observe the maximum speed. The maximum
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.
3 Observe the motor / saw blade direction of rota-
tion.
26 І 48
4 Do not use any insertion tools with cracks. Sort
out cracked insertion tools. Repairs are not per-
mitted.
5 Clean grease, oil and water off of the clamping
surfaces.
6 Do not use any loose reducing rings or bushes
for the reducing of holes on saw blades.
7 Make sure that fixed reducer rings for securing
the insertion tool have the same diameter and
have at least 1/3 of the cutting diameter.
8 Make sure that fixed reducer rings are parallel
to each other.
9 Handle insertion tool with caution. They are ide-
ally stored in the originally package or special
containers. Wear protective gloves in order to im-
prove grip and to further reduce the risk of injury.
10 Prior to the use of insertion tools, make sure that
all protective devices are properly fastened.
11 Prior to use, make sure that the insertion tool
meets the technical requirements of this electric
tool and is properly fastened.
12 Only use the supplied saw blade for sawing oper-
ations in wood, materials similar to wood, plastics
and non-ferrous metals (except for magnesium
and alloys containing magnesium).
6. Remaining hazards
The machine has been built according to the state of
the art and the recognised technical safety require-
ments. However, individual residual risks can arise
during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the „safety in-
structions" and the „Proper use" are observed
along with the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the ma-
chine in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be fixed between the clamps.
• Avoid accidental starting of the machine: the op-
erating button may not be pressed when inserting
the plug in an outlet.
• Use the tool that is recommended in this manu-
al. In doing so, your saw provides optimal perfor-
mance.
• Hands may never enter the processing zone when
the machine is in operation. Release the handle
button and switch off the machine prior to any op-
erations.
• Prior to any adjustment, maintenance or service
work disconnect the mains power plug!
Publicité
