IMG STAGELINE PARL-1DMX Mode D'emploi page 17

7.3 Adjusting the start address
To be able to operate the spotlight with a light controller,
adjust the DMX start address for the first DMX channel.
If e. g. address 17 on the DMX controller is provided for
controlling the red LEDs, adjust the start address 17 on
the PARL-1DMX. The other functions of the spotlight
are then automatically assigned to the following
addresses (in this example 18 to 20). The address 21
could be used in this example as the next possible start
address for the following DMX-controlled unit.
1) Press button MENU (5) once until the display (3)
shows . Make sure that the next button is
pressed within 15 seconds, otherwise the adjusting
process will end.
2) Press button ENTER. The adjusted address is
shown. For automatic adjustment of the address,
continue with step 4.
3) For manual adjustment, use button DOWN or UP
to adjust the address and memorize it with button
ENTER. reappears on the display. After 15 sec-
onds the spotlight returns to the previous operating
mode. For faster switching-over keep button MENU
pressed until the display shows the operating mode.
4) For automatic address adjustment, use button
DOWN or UP to switch to
ful if several PARL-1DMX units are used and their
addresses are intended to be in the lower range.
After selecting the function
ENTER. All LEDs shortly light up and
After 15 seconds the unit is switched back to the
previous operating mode.
The start address of the first spotlight is now
adjusted to 1, the start addresses of the following
spotlights to 5, 9, 13, etc.
Once the control signals of the DMX controller are
received, the red LED DMX (4) lights up and the dis-
play shows the start address. The PARL-1DMX can
now be operated with the DMX controller.
7.4 Control with the LED-4C
The unit LED-4C from "img Stage Line" is an easy-to-
operate control panel which can also be used for the
spotlight PARL-1DMX. It has 4 channels so that all
PARL-1DMX units connected to it can only be con-
trolled in sync.
1) Connect the jack DMX OUTPUT of the LED-4C to
the jack DMX INPUT (10) and switch on the LED-4C.
2) Adjust the start address of the spotlights to 1 or a
multiple of 4 + 1 (5, 9, 13, ... max. 61),
3) To control the PARL-1DMX with the LED-4C, the
DMX mode must be switched on:
. This method is use-
, press button
flashes.
chap. 7.3.
a) Press button MENU (5) so many times until the
display (3) shows
button is pressed within 15 seconds, otherwise
the adjusting process will end.
b) Press button ENTER, the adjusted mode will be
shown ( ...
c) With button DOWN or UP switch to the mode
and memorize it with button ENTER.
reappears on the display. After 15 seconds
the spotlight is switched to the modified operat-
ing mode, the display shows
and a number (1 – 16). The red LED SLAVE (6)
lights up.
Please refer to the instructions for the LED-4C for
more information about the operation.
8 Further Functions
8.1 Display of the operating hours
To show the state of the operating hour counter:
1) Press button MENU (5) so many times until
(fixture hours) is shown on the display (3).
2) Press button ENTER and the operating hours are
shown.
3) After 15 seconds the unit is switched back to the
previous operating mode.
8.2 Display of the firmware version
To show the version number of the firmware (operating
system of the unit):
1) Press button MENU (5) so many times until
(version) is shown on the display (3).
2) Press button ENTER. The version number is
shown, e. g. = version 1.0.
3) After 15 seconds the unit is switched back to the
previous operating mode.
9 Cleaning the Unit
The plastic pane in front of the LEDs should be cleaned
at regular intervals from the outside, depending on
impurities caused by dust, smoke or other particles.
Only this will ensure that the light is radiated at maxi-
mum brightness. For cleaning, disconnect the mains
plug from the socket. Only use a soft, clean cloth and
a mild detergent. Then wipe the plastic pane dry.
For cleaning the other parts of the housing, only use
a soft, clean cloth. Never use any fluid; it may leak into
the unit and cause damage.
. Make sure that the next
).
(= slave mode)
GB
17