Publicité
Les langues disponibles
Les langues disponibles
= music control switched off:
The
programme
adjusted speed.
c) Use button DOWN or UP to switch the music
control on or off and confirm with button ENTER.
The display returns to the indication
15 seconds the selected programme starts and
the display shows again the number of the pro-
gramme. For a quicker start of the programme
keep button MENU pressed until the display
shows the number of the programme.
If the music is played with a clear rhythm in the bass
range at sufficient volume and the music control is
switched on, the selected programme is controlled via
the microphone (7). With each music control pulse the
green LED SOUND (6) shortly lights up. If the music
control should not function in an optimum way,
increase the volume or reduce the distance between
the sound source and the PARL-1DMX.
6.1.2 Colour radiator
The unit is capable of radiating one of 16 preset
colours at maximum brightness or a manually adjusted
colour at any desired brightness.
A Selecting a preset colour
1) Press button MENU (5) so many times until
displayed.
2) Activate the menu item with button ENTER. The
display shows the colour last adjusted (
or
).
3) Select a colour with button DOWN or UP (1 = red ...
16 = white,
next paragraph) and confirm with button
ENTER. The display returns to
onds it shows the selected colour number and the
spotlight radiates the corresponding colour.
B Manual colour adjustment
Hint: When adjusting the brightness of the red, green, or
blue LEDs, not only their brightness will be modified but in
case of a combination of these colours, the shade of colour
will also be modified. Therefore, first adjust the colour which
is intended to dominate to the desired brightness, and then
add the other two colours. For the combination white, first
adjust the brightness of the colour green, because this colour
appears to the eye to be the brightest colour. Then add red
to result in yellow and finally add blue to result in white.
1) Press button MENU (5) so many times until the dis-
play shows
.
2) Activate the menu item with button ENTER. The
display shows the colour last adjusted (
or
) in a flashing way.
3) Use button DOWN or UP to switch to
ual). Activate the function with button ENTER. The
display now shows
4) Use button DOWN or UP to switch to
colour green and to
again to
for red. Select the colour to be
adjusted first.
operates
with
= manual colour adjustment,
. After 15 sec-
(red).
for blue and then back
5) Press button ENTER so that the value of the
selected colour is displayed (indication 0 – 255).
the
Adjust the brightness of the colour with button
DOWN or UP and confirm with button ENTER.
6) Repeat the steps 4 and 5 for the further colours so
. After
that the desired shade of colour with the desired
brightness will result.
7) For fine adjustment of the shade of colour, a colour
can be selected again with button DOWN or UP,
and after pressing button ENTER, it can be read-
justed with the buttons DOWN and UP. Then press
button ENTER again.
8) If no button is actuated within 15 seconds, the dis-
play returns to the indication
shade of colour, start again with step 1, if required.
6.2 Interconnecting several PARL-1DMX units
Several PARL-1DMX units may be interconnected.
Then all slave units can be controlled in sync with the
master unit.
1) Connect the DMX OUTPUT (9) of the master unit
via a 3-pole XLR cable (e. g. series MEC-... or
MECN-... from the product range of "img Stage
Line") to the DMX INPUT (10) of the first slave unit.
is
2) Connect the DMX OUTPUT of the first slave unit to
the DMX INPUT of the second slave unit, etc. until
all units have been connected in a chain.
...
3) Adjust the type of control at the slave units.
a) Press button MENU (5) so many times until the
indication
b) Press button ENTER. The display now shows
the adjusted slave mode (
c) Adjust the desired mode with button UP or
DOWN:
= The slave unit is controlled in sync by
= Stroboscopic
...
No DMX signal must be present at the DMX INPUT of
the master unit, so that the yellow LED MASTER (4)
lights up and the unit is thus switched to the master
mode. Once the control signals from the master unit
are applied to the slave units, the red LED SLAVE (6)
will light up on the slave units. The slave units are then
...
automatically switched to the slave mode and can be
controlled with the master unit accordingly.
(man-
for the
is shown on the display (3).
the master unit.
effects
opposite to the master unit.
= The control is optimized for the
use of 3 to 16 slave units.
GB
. To change the
...
).
are
controlled
15
Publicité
