ST EL 340 Li 48L Manuel D'utilisation page 40

IMPORTANT Damaged or illegible labels must be replaced..
Order replacement decals from an authorised service centre.
3. ASSEMBLY
IMPORTANT Unpacking and assembly must be carried out
on a flat, solid surface with sufficient space to move the machine
and the packaging.
1. Unpacking (Fig. 2)
2. Assembling and adjusting the handle (Fig. 3)
3. Grass catcher assembly (Fig. 4)
4. CONTROLS
• Safety key (Deactivation device)
The safety key found inside the battery compartment enables
/ disables the machine electric circuit (Fig. 5).
Removing the key, the electric circuit is completely deactivated
to prevent uncontrolled use of the machine.
IMPORTANT Remove the safety key whenever the machine
is unused or left unattended.
• Operator presence lever
The operator presence lever enables the engagement of the
cutting device. The handle is located in the front position.
Press the safety button and move the lever towards the handle
to start the cutting device. (Fig. 6)
When the lever is released, the motor automatically stops
and all functions are disabled.
• Cutting height adjustment
By lowering or raising the chassis the grass can be cut at
different heights. (Fig. 7)
IMPORTANT This operation must be carried out when the
cutting device is stationary.
5. USING THE MACHINE
IMPORTANT For instructions regarding the engine and the
battery (if supplied), read the relevant manual.
5.1. PRELIMINARY PROCEDURES
Place the machine in a stable horizontal position on the ground.
• Checking the battery
Before using the machine for the first time after purchase,
fully charge the battery following the instructions in the
battery booklet.
Before every use of the machine, check the battery charge
status according to the instructions in the battery booklet.
• Preparing the machine before starting work
IMPORTANT Carry out this operation with the cutting de-
vice stationary.
With this machine, it is possible to mow the lawn in several ways:
• Setting up for cutting the grass and collecting it in the
grass catcher (Fig. 8)
• Setting up for cutting and rear grass discharge onto the
ground (Fig. 9)
• Setting up for cutting and shredding the grass ('mulching'
function) (Fig. 10)
5.2. SAFETY CHECKS
• Check the integrity and correct assembly of all machine
components;
• Make sure that all fasteners are tightened correctly;
• Keep every surface of the machine clean and dry.
Action
1. Start the machine.
2. Release the switch control.
1. Start the machine.
2. Engage the drive lever.
3. Disengage the drive lever.
1. Test drive.
If any of the results fail to match the indications
provided in the tables, do not use the machine!
Contact a service centre to have it checked and
repaired if necessary.
5.3. START-UP AND WORK
NOTE Start the machine on a level surface free from obsta-
cles or grass.
Start the machine as shown in (Fig. 11).
IMPORTANT Always maintain a safe distance from the cut-
ting device while working, corresponding to the length of the
handle.
Emptying the grass catcher
(Fig. 12)
1. Release the switch lever and wait for the cutting device
to stop.
2. Lift the rear discharge guard, take hold of the handle and
remove the grass catcher by holding it in an upright position.
5.4. STOP
At the end of the work, release the switch control (Fig. 13).
When you have stopped the machine, it will take
a few seconds for the cutting means to stop.
5.5. AFTER OPERATION
• Cleaning procedure (Par. 6.1).
• If necessary, replace the damaged components and tighten
any loose screws and bolts.
Whenever you leave the machine unused or unattended:
• Open the battery housing hatch and remove the safety key
(for battery models).
6. MAINTENANCE
The safety regulations to follow are described in chap. 1. Strictly
comply with these indications to avoid serious risks or dangers.
Before conducting any inspections, cleaning or maintenance/
adjustment interventions on the machine:
• Stop the machine.
EN - 4
Result
1. The cutting means should
move.
2. The levers must return to the
neutral position automatically
and quickly, the engine must
switch off and the cutting
device must stop within a few
seconds.
2. The machine moves forward.
3. The machine comes to a
standstill.
1. No abnormal vibrations.
No abnormal sound.