Publicité
Les langues disponibles
Les langues disponibles
DEOS
Sound pressure level (L
pA
Sound power level (L
)
WA
Sound measurement uncertainty K
Vibration emission value a
Vibration emission uncertainty K
Specifications subject to change without prior notice. Model range may vary between markets.
*
The values stated in the table are derived from laboratory testing in conformity with stated codes and standards and
are not sufficient for risk evaluation. Values measured in a particular work place may be higher than the declared
values. The actual exposure values and amount of risk or harm experienced by an individual are unique to each
situation and depend upon the surrounding environment, the way the individual operates the machinery, the par-
ticular material being worked, work station design and the user's exposure time and physical condition. Mirka Ltd
accepts no responsibility for the consequences of using declared values instead of actual exposure values for any
individual risk assessment.
Further occupational health and safety information can be obtained from the following websites:
https://osha.europa.eu/en (Europe) or http://www.osha.gov (USA)
Proper use of tool
This sander is designed for sanding all types of materials, i.e. metals, wood, stone, plastics, etc. using abrasives designed
for this purpose. Do not use this sander for any other purpose than that specified without consulting the manufacturer
or the manufacturer s authorized supplier. Only use original Mirka backing pads that are designed for optimal performance.
Other backing pads may reduce performance and will increase vibration. The cooling air vents on the housing must be
kept clean and free of blockages to ensure air circulation. Repair work may only be carried out by an authorized service
center.
Work stations
The tool is intended to be operated as a hand-held tool. It is always recommended that the tool should be used when
standing on a solid floor. It can be in any position but before any such use, the operator must be in a secure position,
having a firm grip and footing and be aware that the tool can develop a torque reaction. See the section Operating
instructions .
How to get started
When unpacking the tool, make sure it is intact, complete and has not been damaged in transport. Never use a damaged
tool.
Before use, check that the backing pad is correctly attached and tightened. Connect the power cord to the tool. Connect
the power cord to a grounded outlet (230 VAC, 50 60Hz).
In order to get the maximum power from this tool it is recommended to use it with the Mirka dust extractor (or other
suitable dust extraction unit) and Mirka net sanding products. The combination of Mirka sanders, Mirka net sanding
products and Mirka dust extractor are the basis of Mirka dust-free sanding solutions.
The power cord from the tool is connected to the mains supply of the dust extractor. By connecting the tool's power cord
to the outlet on the dust extractor it is possible to use the dust extractor s autostart function.
Operating instructions
The tool is intended to be operated as a hand held tool. The tool can be used in any position. Note! The sander can
develop a torque reaction when started.
Make sure the sander is switched off. Select a suitable abrasive and secure it to the backing pad. Make sure the abrasive
is centred on the backing pad. For optimal performance we recommend a Mirka backing pad and Mirka Net Sanding
product.
Switch on the sander by pressing the On/Off key, Figure 1. The sander LED (right) is now green.
The sander can now be started by pressing the lever.
343CV
)
70 dB(A)
81 dB(A)
3.0 dB(A)
*
2
3.3 m/s
h
*
2
1.5 m/s
353CV
383CV
69 dB(A)
71 dB(A)
80 dB(A)
82 dB(A)
3.0 dB(A)
3.0 dB(A)
2
2.6 m/s
2.6 m/s
2
1.5 m/s
1.5 m/s
663CV
68 dB(A)
79 dB(A)
3.0 dB(A)
2
2
2.6 m/s
2
2
1.5 m/s
Mirka® DEOS 343, 353, 383 & 663
en (original)
55
Publicité
