stayer LP700 Manuel D'instructions Original page 14

gb
NOTE: Only use sandpaper discs which fit properly and
which are designad far vacuum use.
Change of brush ring
The brush bristles on the edge of the sanding plata cover
serve two purposes, they keep the sanding disc properly
aligned with the work surface without gouging and they
also help the efficiency of the dust collection by the vacuum
cleaner. These brush bristles will wear with continuad use.
The sanding plata cover should be replaced when the
bristles are too worn to ensure effective dust collection and
stabilization of the sanding head.
Replacement is the opposite of removal. Entrust all repairs
to an authorized service centre.
Remove the brush ring by removing the 6 or 8-star screws.
Sanding pad change
- Insert a hex key into the center screw with hex nut on the
sanding pad.
- Insert a rod, allen key or screwdriver in one of the suc-
tion holes to immobilize the plate, holding the tool with your
hand.
- Turn the hex key to remove the chainring.
- Install the new sanding by tightening the central screw.
Speed setting
The speed of the machine varies to suit different tasks
using the wheel. The highest speed should be used for a
fast, coarse sanding and the lowest speed for more precise
control and a finer finish.
5_INSTRUCTIONS OF USE
Effective control of this powerful tool requires two-handed
tor maximum safety and control.
Always wear respiratory mask and glasses with EPI level.
Once the machi ne and vacuum cleaner are set up and
all safety measures and equipment are in place, begin by
turning on the vacuum cleaner and then the machine. (lf
you are using a vacuum cleaner with integrated switching,
then simply turn the machine on.)
Begin sanding and carefully contact the work surface as
lightly as possible-just enough to keep the sanding head flat
against the surface.
The joist in the sanding head allows the sanding disc to
follow the contours of the work surface.
The best technique is to use overlapping sweeps and
keep the head in constant motion. Never stop too long in
any one place ar there will be swirl marks. With
experience it will be very easy to create excellent results.
For a better job in the joints between walls and / or ceilings
in the LP1000E model, a part of the brush ring can be
removed to gain access to the 100% joint. To remove,
release the tab on the top of the sanding head to remove
the part.
NOTE: Ensure that the sandpaper you are using is suited to
the task, overly coarse grit paper may remove material too
quickly to control. While overly fine grit paper may clog too
often and not shape down the surface.
CAUTION: Take care to avoid sharp projections and nails,
etc.This will wipe out the sandpaper and probably damage
the sponge pad as well.
ELIMINATION
We recommend that the power tools, accessories and
packaging should be a recovery process that respects the
environment.
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directiva 2012/19/UE
on Waste Electrical and Electronic Equipment
and its implementation into national law, must
accumulate separately far power tools under an
ecological recycling.
Subject to modification.
6_MAINTENANCE INSTRUCTIONS
CLEANING, MAINTAINING, LUBRICATING,
SHARPENING
Before any work on the machina itself, pull the mains plug.
For safe and proper working, always keep the machina
and ventilation slots clean.
In extreme working conditions, conductiva dust
can accumulate in the interior of the machina when
working with metal. The protective insulation of the
machi ne can be degradad. The use of a stationary
extraction system is recommended in such cases as
well as frequently blowing out the ventilation slots and
installing a residual current device (RCD).
Conservare e trattare con cura l'accessorio.
Please store and handle the accessory(-ies) carefully.
lf the machine should fail despite the care
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for STAYER
power tools.
REPAIR SERVICE
The technical service will provide you advice regarding
questions you may have on the repair and maintenance
of your product as well as on spare parts. You may also
obtain exploded views and information on spare parts on
the internet under: info@grupostayer.com
Our team of technical advisors will be glad to guide you
regarding acquisition, application and adjustment of
products and accessories.
The warranty is limited only to manufacturing defects and
expire if pieces have been removed or manipulated or
repaired other than the manufacturar.
- 14 -
taken in