SOLAC Optima Station 6.0 Mode D'emploi page 12

ENGLISH
ECO
Select the ECO setting for optimal ironing per-
•
formance, only select it between the points ••
and MAX.
The ECO function uses less energy, but ensur-
•
ing sufficient steam
to iron your clothes properly. Only activate this
•
function when the boiler and iron temperatures
are correct. The ECO function can be used
with all types of fabrics. Nonetheless, for very
thick or heavily creased fabrics we recommend
that you use the maximum steam output func-
tion to ensure optimal results
ONCE YOU HAVE FINISHED USING THE AP-
PLIANCE:
Select the minimum position (MIN) using the
•
thermostat control.
Turn the appliance off, using the on/off switch.
•
Unplug the appliance from the mains.
•
Put the cable back in the cable housing. .
•
Remove the water from the water tank.
•
Clean the appliance.
•
CABLE COMPARTMENT
This appliance has a cable compartment situ-
•
ated on its posterior. (E)
PRACTICAL RECOMMENDATIONS:
Classify the garments into groups by ironing
•
temperature. The appliance heats up more
quickly than it cools down, therefore, to avoid
accidents, minimise energy consumption and
optimise time, it is advisable to start off ironing
items that require lower temperatures and pro-
gress to those that need higher temperatures.
Pure wool fabrics (100%) can be ironed with
•
the iron set to steam. Select a high steam tem-
perature and place a cotton cloth between the
iron's metal surface and the garment.
SAFETY THERMAL PROTECTOR:
The appliance has a safety device, which pro-
•
tects the appliance from overheating.
TRANSPORTATION
Place the iron correctly into its transportation
•
system and lock it, making sure it is seated
correctly, and lift it upright by holding the iron
handle..
CLEANING
Disconnect the appliance from the mains and
•
allow it to cool before undertaking any cleaning
task (Fig.4).
Clean the equipment with a damp cloth with a
•
few drops of washing-up liquid and then dry.
Do not use solvents, or products with an acid
•
or base pH such as bleach, or abrasive prod-
ucts, for cleaning the appliance.
Never submerge the appliance in water or any
•
other liquid or place it under running water.
HOW TO DEAL WITH LIME SCALE INCRUS-
TATIONS:
For the appliance to work correctly it should be
•
kept free of limescale or magnesium incrusta-
tions caused by the use of hard water.
To avoid this kind of problem it is advisable to
•
use distilled water.
However, if it is not possible to use the kind of
•
water recommended above, you should peri-
odically remove the limescale from the appli-
ance.
A specific anti-lime scale product should be
•
used on this kind of product.
Homemade solutions are not recommended in
•
the decaling of this appliance, such as the use
of vinegar.
CLEANING THE BOILER
Check that appliance has cooled down (wait
•
at least 3 hours after disconnecting the appli-
ance).
Empty the water tank and after the boiler (O).
•
To empty the boiler, unscrew the cleaning cap
•
(F) in an anti-clockwise direction
Empty the boiler and close it by screwing the
•
cleaning cap by follow the previous procedure
in reverse (Fig.5).
Fill the water tank (O) with approximately
•
500ml of water and add the selected anti-lime
scale product.
Connect the appliance (with the maximum se-
•
lected steam) and wait for 20 minutes approxi-
mately in order for the anti-scale product begin
to take effect.
Let all the steam out (in a suitable place, for
•
example the sink) until the water tank is empty.
Wait the appliance to cooled down, rinse the
•
water tank and boiler with cold water.
ANOMALIES AND REPAIR
Take the appliance to an authorised technical
•
support service if product is damaged or other
problems arise. Do not attempt to disassemble
or repair the appliance yourself as this may be
dangerous.
EN