ST MP2 500 Li D48 Serie Manuel D'utilisation page 42

If something breaks or an accident occurs during
mowing, turn off the engine immediately and move
the machine away to prevent further damage; if
an accident occurs with injuries or third parties
are injured, carry out the first aid measures most
suitable for the situation immediately and contact
the medical authorities for any necessary health
care. Carefully remove any debris which could
cause damage or injury to persons or animals
if ignored.
1.4. MAINTENANCE, STORAGE AND TRANSPORT
Ensure regular maintenance and correct storage to maintain
machine safety and high performance levels.
• Never use the machine with worn or damaged parts. Faulty
or worn-out parts must always be replaced and never
repaired. Only use original spare parts.
• While adjusting the machine, pay attention to avoid getting
your fingers caught between the moving cutting device and
the fixed parts of the machine.
• To reduce fire risks, do not leave containers with debris
inside a room.
The noise and vibration levels shown in these
instructions are the maximum levels for use of
the machine. The use of an unbalanced cutting
element, the excessive speed of movement, or
the absence of maintenance have a significant
influence on noise emissions and vibrations.
Consequently, it is necessary to take preventive
steps to eliminate possible damage due to high
levels of noise and stress from vibration. Maintain
the machine well, wear ear protection devices,
and take breaks while working.
1.5. BATTERY / BATTERY CHARGER
IMPORTANT The following safety instructions are an addition
to the safety requirements provided in the specific battery and
battery charger manual delivered with this machine.
• Only use battery chargers recommended by the
manufacturer to recharge batteries. An inadequate battery
charger may cause electric shock, overheating or corrosive
liquid to leak from the battery
• Use only batteries specifically designed for your power tool.
The use of other batteries may cause injuries and fire risks.
• Make sure that the machine is switched off before inserting
the battery. Inserting a battery in a machine which is switched
on can cause a fire.
• Keep all unused batteries at a distance from paper clips,
coins, keys, nails, screws or other small metal objects as
contact with the same can cause short circuits. Short circuits
between battery contacts can lead to explosion or fires.
• Never use the battery charger in environments in the
presence of vapours, flammable substances or on easily
flammable surfaces such as paper, fabric, etc. The battery
charger heats up during recharging and may cause a fire.
• When transporting accumulators, make sure the contacts
never come into contact with each other and never use
metal containers to transport them.
1.6. POWER SUPPLY
• Keep the extension lead away from the cutting means. The
cutting means can damage the cable and cause contact
with energised parts.
• Never run the lawnmower over the electric cable. While
mowing, always drag the cable behind the lawnmower on
the side where the grass has already been cut. Use the
cable fastener to prevent the cable from disconnecting
accidentally as indicated in this manual. Make sure it is
connected to the socket without being forced.
• Power up the machine using a differential switch (RCD -
Residual Current Device) with a tripping current of max.
30 mA.
• Machine plugs must always match the relative outlets. Never
modify the plug in any way. Do not use any adapter plugs
with earthed (grounded) machines. Unmodified plugs and
matching outlets will reduce risk of electric shock.
• If the machine's power cable is damaged, it can only be
replaced with an original spare part by your dealer or an
authorised service centre.
• The permanent connection of any electrical equipment
to the mains of a building must be installed by a qualified
electrician in conformity with the regulations in force.
Incorrect wiring can cause serious injury and even death.
• Warning: Moisture and electricity are not compatible:
Always handle and connect electric cables in dry conditions.
- Never allow electric sockets or cables to come into contact
with wet areas (puddles or wet grass).
- Connections between cables and sockets must always be
watertight. Only use extension leads with intact, watertight
and approved sockets sold on the market.
• The quality of the power cables must be no less than
H07RN-F or H07VV-F, with a minimum section of 1.5 mm²
and a recommended maximum length of 25 m.
• Do not use the cable improperly. Never use the cable for
carrying, pulling or unplugging the machine. Keep the cable
away from heat, oil, sharp edges or moving parts. Damaged
or entangled cables increase the risk of electric shock.
• Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, cookers and refridgerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
• Before use check the supply cable and extension lead
for signs of damage or aging. If the cable or lead become
damaged during use, disconnect the plug from the mains
socket immediately. DO NOT TOUCH THE CABLE
BEFORE DISCONNECTING IT FROM THE MAINS
SUPPLY SOCKET. Never use the machine if the power
cable or extension lead are damaged or worn. Damaged or
deteriorated cables may cause contact with energised parts.
EN - 2