Publicité
Les langues disponibles
Les langues disponibles
Troubleshooting
Problem
Pump has following
problems: failure to
produce pressure, loss
of pressure, low water
volume.
Detergent fails to mix
with spray.
Engine will not start;
starts and runs rough
or shuts down during
operation.
For all other issues, see an authorized dealer.
Specifications
°
Green, 25
°
Red, 0
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2200 PSI (152 bar) @ 2.0 GPM (7.6 L/min)*
Water Supply Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41°F (5°C) - 100°F (38°C)
min Water Supply Flow Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 GPM (11.35 L/min)
min Water Supply Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 PSI (1.38 bar)
Engine Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.74 in
Spark Plug Gap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.030 in. (0.76 mm)
Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 oz (0.6 L)
*This pressure washer is rated in accordance to the Pressure Washer Manufacturers' Association (PWMA) standard
PW101-2018 (Testing and Rating Performance of Pressure Washers).
Cause
1. Low pressure spray tip installed.
2. Inadequate water supply.
3. Clogged inlet hose screen.
4. Spray tip is obstructed.
5. Connections leak.
6. High pressure hose or spray gun
leaks.
1. High pressure spray tip installed.
2. Check ball stuck in detergent
siphoning system.
3. Detergent siphoning tube is clogged
or cracked.
1. Engine switch set to off (0) position.
2. Fuel shut-off lever is in off position.
3. Low oil level.
4. Dirty air cleaner.
5. Out of fuel.
6. Spark plug wire not connected to
spark plug.
7. Flooded with fuel.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2200 PSI (152 bar) @ 2.0 GPM (7.6 L/min)*
Correction
1. Replace with high pressure spray tip.
2. Provide adequate water flow.
3. Check and clean inlet hose screen.
4. Clean spray tip. See Spray Tip Maintenance.
5. Tighten connections or replace o-rings.
6. Replace.
1. Replace with low pressure black spray tip.
2. Free check ball. See Detergent Siphoning
Check Ball.
3. Clean or replace detergent siphoning tube.
1. Set switch to on (I) position.
2. Move fuel shut-off lever to on position.
3. Fill crankcase to proper level or place
pressure washer on level surface.
4. Clean or replace air cleaner.
5. Fill fuel tank.
6. Connect wire to spark plug.
7. Wait 5 minutes and re-crank engine.
3
(127 cc)
15
Publicité
