Kärcher RCV 3 Mode D'emploi page 21

Dry wipe
1. Empty the dust container if necessary, see chapter
Emptying the 2-in-1 dust container with water reser-
voir.
2. Insert the dry wiper cloth into the wiper cloth holder,
see chapter Installing the wiper cloth holder with
wiper cloth.
3. Press the On/Off button.
The cleaning robot starts cleaning.
Wet wipe
Note
After emptying the water reservoir, drops may remain in
the hoses. If the cleaning robot is started with an empty
water reservoir, these drops can be discharged.
ATTENTION
Damage to the 2-in-1 dust container due to corro-
sion and chemical content materials
Do not put detergents, disinfectants or other cleaning
products into the 2-in-1 dust container.
Do not pour hot water into the 2-in-1 dust container.
Do not immerse the 2-in-1 dust container in water.
1. Press any button.
The cleaning robot stops.
2. Remove the 2-in-1 dust container with water reser-
voir.
Illustration G
a Open the cover at the top.
b Press the clamp.
c Remove the 2-in-1 dust container with water res-
ervoir.
3. Refill water.
Illustration M
a Pull up the rubber tab.
b Fill with water.
c Press the rubber tab down.
4. Install the 2-in-1 dust container with water reservoir.
Illustration F
a Press the 2-in-1 dust container with water reser-
voir into position until it audibly latches into place.
b Close the cover at the top.
5. Dampen the wiper cloth under running water and
wring out to remove excess water.
6. Install the wiper cloth, see chapter Removing the
wiper cloth holder with wiper cloth.
7. Press the On/Off button.
The cleaning robot starts cleaning.
Refilling water
1. Press any button.
The cleaning robot stops.
2. Remove the 2-in-1 dust container with water reser-
voir.
Illustration G
a Open the cover at the top.
b Press the clamp.
c Remove the 2-in-1 dust container with water res-
ervoir.
3. Refill water.
Illustration M
a Pull up the rubber tab.
b Fill with water.
c Press the rubber tab down.
4. Install the 2-in-1 dust container with water reservoir.
Illustration F
a Press the 2-in-1 dust container with water reser-
voir into position until it audibly latches into place.
b Close the cover at the top.
5. Press the On/Off button.
Cleaning continues.
Emptying the 2-in-1 dust container with water
1. Press any button.
The cleaning robot stops.
2. Remove the 2-in-1 dust container with water reser-
voir.
Illustration G
a Open the cover at the top.
b Press the clamp.
c Remove the 2-in-1 dust container with water res-
ervoir.
3. Empty the 2-in-1 dust container with water reservoir.
Illustration N
a Open the filter flap.
b Remove the filter flap.
c Empty the 2-in-1 dust container with water reser-
voir.
d Fit the filter flap.
e Close the filter flap.
4. Install the 2-in-1 dust container with water reservoir.
Illustration F
a Press the 2-in-1 dust container with water reser-
voir into position until it audibly latches into place.
b Close the cover at the top.
5. Press the On/Off button.
Cleaning continues.
Emptying the dust container
1. Press any button.
The cleaning robot stops.
2. Remove the dust container.
Illustration L
a Open the cover at the top.
b Press the clamp.
c Remove the dust container.
3. Empty the dust container.
Illustration O
a Fold the flap down.
b Empty the dust container.
c Fold the flap upwards until it audibly latches into
place.
4. Install the dust container.
Illustration K
a Press the dust container into position until it audi-
bly latches into place.
b Close the cover at the top.
5. Press the On/Off button.
Cleaning continues.
Cleaning the wiper cloth
The wiper cloth can be cleaned during a cleaning pro-
cess.
1. Press any button.
The cleaning robot stops.
2. Remove the wiper cloth holder.
Illustration J
a Press the clamps together.
b Remove the wiper cloth holder.
c Pull the wiper cloth off the wiper cloth holder.
3. Clean the wiper cloth.
4. Install the wiper cloth, see chapter Installing the
wiper cloth holder with wiper cloth.
5. Press the On/Off button.
Cleaning continues.
English
reservoir
21