Kärcher RCV 3 Mode D'emploi page 20

Note
Only 2.4 GHz WLAN networks are supported.
1. Switch on the cleaning robot, see chapter Switching
on the cleaning robot.
2. Press the On/Off button and the "Return to charging
station" button simultaneously for 7 seconds until a
voice says: "Resetting the WLAN connection and
entering network configuration mode".
3. Connect the cleaning robot to the charging station,
see chapter Connecting the cleaning robot with the
charging station.
Restoring the factory settings
1. Press and hold the "Return to charging station" but-
ton for 5 seconds until a signal sounds.
2. Press and hold the "Return to charging station" but-
ton again for 5 seconds until a signal sounds.
Factory settings are restored.
Setting up cleaning zones
The cleaning robot only cleans within the selected area.
Cleaning zones can only be set up with the App. Down-
loading the App is described in the chapter Connecting
cleaning robots with WLAN and App.
 Follow the step-by-step instructions in the App.
Setting up virtual walls
Virtual walls and restricted areas prevent the cleaning
robot from entering areas that should not be cleaned.
Virtual walls can only be set up with the App. Download-
ing the App is described in the chapter Connecting
cleaning robots with WLAN and App.
 Follow the step-by-step instructions in the App.
Activating mapping
The cleaning robot starts from the charging station and
automatically updates its map after completing a clean-
ing task and after charging.
Mapping can only be set up with the App. Downloading
the App is described in the chapter Connecting clean-
ing robots with WLAN and App.
Note
To avoid losing the map, wait a few seconds after the
first mapping until the map is saved.
 Follow the step-by-step instructions in the App.
Operation
ATTENTION
Damage due to moisture
Remove the wiper cloth with wiper cloth holder before
charging and when not in use, see chapter Removing
the wiper cloth holder with wiper cloth.
Remove the 2-in-1 dust container with water reservoir
before charging and when not in use, see chapter Re-
moving the 2-in-1 dust container with water reservoir.
Protect carpets using virtual walls, see chapter Setting
up virtual walls.
Switching on the cleaning robot
Note
Place the cleaning robot directly on the charging station
if it cannot be switched on due to a too low charging
state, see chapter Initial start-up.
1. Keep the On/Off button pressed when the cleaning
robot is in standby and not on the charging station.
The indicator light flashes for approx. 15 seconds
while the cleaning robot starts up and then lights up
constantly.
20
The cleaning robot emits an acoustic signal when
the start-up is complete.
2. Place the cleaning robot directly on the charging
station.
3. Press the On/Off button.
At initial Start-Up, the cleaning robot starts mapping.
In operation, the cleaning robot starts cleaning.
Setting cleaning modes
Cleaning modes can only be set up with the App. Down-
loading the App is described in the chapter Connecting
cleaning robots with WLAN and App.
The following cleaning modes are available:
● Dry cleaning
● Combination cleaning
● Wet cleaning
The suction power and water quantity can be set in each
of the cleaning modes.
Suction power:
● Quiet
● Standard
● Medium
● Turbo
Water quantity:
● Low
● Medium
● High
Switching off the cleaning robot
Note
The cleaning robot cannot be switched off when it is on
the charging station.
Note
Fully charge the cleaning robot before longer work inter-
ruptions.
ATTENTION
Damage due to moisture
Remove the wiper cloth with the wiper cloth holder, see
chapter Removing the wiper cloth holder with wiper
cloth.
Remove the 2-in-1 dust container with water reservoir,
see chapter Removing the 2-in-1 dust container with
water reservoir.
1. Keep the On/Off button pressed when the cleaning
robot is in standby and not on the charging station.
The cleaning robot switches off.
Interrupting cleaning
1. Press any button during cleaning.
The cleaning robot stops.
2. Press the On/Off button.
Cleaning continues.
3. Press the "Return to charging station" button.
Cleaning is cancelled and the cleaning robot returns
to the charging station.
Manually sending the cleaning robot for
1. If the cleaning robot is moving, press any button.
The cleaning robot stops.
2. Press the "Return to charging station" button.
The cleaning robot moves to the charging station for
recharging.
The cleaning robot automatically returns to the charging
station for recharging when it has completed a cleaning
task or when it is low on energy during a cleaning pro-
cess.
English
recharging