Kärcher RCV 3 Mode D'emploi page 18

Scope of delivery
The scope of delivery for the appliance is shown on the
packaging. Check the contents for completeness when
unpacking. If any accessories are missing or in the
event of any shipping damage, please notify your deal-
er.
Device description
Illustration A
Collision sensor
1
Infrared sensor
2
Laser sensor (LiDAR)
3
Top cover
4
Side brush
5
Steering roller
6
Battery compartment
7
Brush
8
Fall sensor
9
Wiper cloth
10
Wiper cloth holder
11
Battery terminals
12
Brush cover
13
On/Off button
14
"Return to charging station" button
15
Cleaning tool
16
2-in-1 dust container with water reservoir
17
Dust container
18
Charging station
19
Mains plug
20
Functional description
The device consists of a charging station and a battery-
powered cleaning robot.
The mobile cleaning robot obtains its energy from a
built-in rechargeable battery. The cleaning robot can
clean for up to 120 minutes with a single battery charge.
It automatically returns to the charging station to re-
charge when the battery charge decreases.
The cleaning robot moves systematically. It scans the
room with a laser sensor (LiDAR) and then cleans the
room step-by-step. It avoids obstacles that are at least
as high as the LiDAR tower.
The flat design of the cleaning robot allows it to clean
under furniture such as beds, sofas and cupboards.
The cleaning robot has fall sensors that detect stairs
and steps and can prevent falls, as well as collision sen-
sors that detect and avoid obstacles.
The battery for the cleaning robot is charged in the
charging station.
If the cleaning robot starts the cleaning work from the
charging station, it returns to the charging station when
the battery charge is insufficient.
As soon as the charging process is finished, the clean-
ing robot automatically leaves the charging station and
continues the cleaning work. The cleaning robot also re-
turns to the charging station when it has finished clean-
ing.
18
LED display
Lights up blue
Flashes blue slowly
Flashes blue fast
Flashes green slowly Cleaning robot charging
Lights up green
Flashes red slowly
Flashes red fast
The cleaning robot automatically switches to sleep
mode after 5 minutes of inactivity. Press any button to
wake it up.
● The cleaning robot does not switch to sleep mode
when it is on the charging station.
● The cleaning robot switches off automatically if it is
in sleep mode for more than 6 hours
If the cleaning robot encounters an error during opera-
tion, the display flashes red and a signal sounds.
For a solution, see chapter Troubleshooting guide.
If no action is taken within 5 minutes, the cleaning robot
automatically switches to sleep mode.
"Do not disturb" mode
The "Do not disturb" mode is set by default. In "Do not
disturb" mode, the cleaning robot does not resume an
interrupted cleaning, does not perform scheduled clean-
ing and does not give audible warnings.
"Do not disturb" mode can be deactivated in the App.
Downloading the App is described in the chapter Con-
necting cleaning robots with WLAN and App.
Installing the side brush
Illustration B
1. Turn the cleaning robot upside down.
Note
To avoid damage, do not place the robot on the laser
sensor (LiDAR).
2. Fit the side brush.
Setting up the charging station
WARNING
TheRCV 3 cleaning robot may only be charged on the
charger of a charging station with the part number
9.773-007.0.
● Select the location so that the cleaning robot can
easily reach the charging station.
● Ensure a distance of at least 0.5 m to the left and
right of the charging station and a distance of at
least 1.5 m in front of the charging station.
● The location must not be exposed to direct sunlight.
1. Set up the charging station.
Illustration C
2. Plug the mains cable device plug into the cable
holder on the side of the charging station.
Illustration D
3. Connect the mains plug.
English
Status displays
Status
Driving autonomously
Autonomous driving paused
WLAN connection mode
Cleaning robot fully charged or
successfully connected
Battery too empty to start
Error situation
Functions
Sleep mode
Error mode
Initial start-up