Inglesina APTICA Manuel D'instructions page 36

HANDLE AND HOOD ADJUSTMENT
fig. 28 To adjust both the handle and the carrycot hood,
press the two internal buttons simultaneously (C6).
fig. 29 Caution: Before carrying or lifting the carrycot,
always check that the handle is in its vertical position and
properly locked on both sides.
ATTACHING THE APRON
fig. 30 To fit the apron (D) on the carrycot, first fix the press
studs (D2) and then the two slot buttons (D3).
fig. 31 The front flap of the apron (D1) can be extended
and fixed in a position that protects your child from the cold.
fig. 32 To facilitate access to the child, the apron can be
partially folded, detaching only the two side press studs (D2).
The apron stays fixed to the carrycot through the two slot
buttons (D3).
BACKREST ADJUSTMENT
fig. 33 Operate the lever (C6) to adjust the backrest: once
the desired position is reached, set the lever to the starting
position.
CARRYCOT VENTILATION
The Aptica carrycot features a coordinated
ventilation system.
fig. 34 The ventilation of the base can be
adjusted using the lever (C7) at the front.
fig. 35 If present: The two mesh inserts on the
back and on the hood permit greater circulation
of air inside the carrycot.
MATTRESS AND INTERNAL LINING MAINTENANCE
It is advisable to remove the mattress and internal lining
periodically for correct maintenance.
fig. 36 To remove the internal lining simply release it from
the edge of the carrycot.
CARRYCOT LINING MAINTENANCE
fig. 37 If it is necessary to remove the carrycot cover,
simply pull it off by unfastening the perimeter straps from
the seats on the structure.
fig. 38 When refitting it, ensure that the two elastic loops
(C8) are fitted perfectly underneath the lower tabs (C9) on
both attachment devices.
Caution! Incorrect positioning of the elastic loops could
interfere with correct attachment of the carrycot to the
chassis.
ALL SEASON STROLLER SEAT
ATTACHING THE STROLLER SEAT TO THE CHASSIS
fig. 39 Attach the stroller seat (E) to the chassis,
positioning it in the dedicated housings on both sides of the
structure.
ADJUSTING THE BACKREST
fig. 40 The backrest can be adjusted to 4 positions; use
the central device (E1) and bring the backrest to the desired
position.
fig. 41 Caution: before use, make sure that the stroller
seat is properly attached on both sides by pulling it
upwards.
DETACHING THE STROLLER SEAT FROM THE CHASSIS
fig. 42 Operate the lever (E2) and simultaneously lift the
stroller seat from the chassis.
Caution: do not, under any circumstance, carry out this
operation with the baby inside.
fig. 43 The stroller seat can be used both facing the parent
and facing the street.
36
ADJUSTING THE FOOTREST
fig. 44 To lower the footrest, use both levers (E3)
positioned on the lower part and simultaneously press them
downwards.
fig. 45 To lift the footrest, simply pull it upwards and it
shall automatically lock into position.
SAFETY BELTS
fig. 46 Ensure that the safety belts are inserted in the
eyelets at the height of the shoulders or immediately above.
If the position is not correct, remove the belts from the first
pair of eyelets and reinsert them in the second one.
Position both back straps always at the same height.
fig. 47 Fit the ends of the back straps (E4) and of the waist
straps (E5) in the central buckle (E6).
fig. 48 Always use the waist strap together with the back
harness, adjusting both of them properly.
Caution! Failure to observe this precaution could cause
your baby to fall or slip, risking injury.
Caution: adapt the height and the length of the harness
according to the baby's growth.
ATTACHING THE HANDRAIL
fig. 49 To attach the bumper bar (G), fit it in the dedicated
housings (G2) in the stroller seat until it clicks into place.
fig. 50 The handrail can be open on one side or fully
removed; to open it, press the button (G1) and remove it
from its housing; to remove it, repeat the procedure on the
other side.
ATTACHING THE STROLLER HOOD
fig. 51 To secure the hood (J), go next to the side joints
(J1) on the stroller seat, fit the strap (J2) and push strongly
until it clicks completely.
fig. 52 First button the press studs (J3) to the side joints
(J1), then all rear buttons (J4) to the backrest.
fig. 53 To adjust the hood, simply accompany it to the
desired position.
fig. 54 The hood features an additional fabric insert
and sun shade that extend the degree of cover, improving
protection from the sun.
DETACHING THE HOOD FROM THE STROLLER
fig. 55 To remove the hood (J) from the stroller seat,
remove all the buttons (J4) that secure it to the backrest.
fig. 56 Remove the two snap fasteners (J3) that secure the
hood to the side joints (J1), then pull the internal strap (J2)
from the joints, pulling it firmly from both sides.
HOOD LINING MAINTENANCE
The hood lining can be removed to allow for its correct
maintenance.
fig. 57 Once the hood is released from the stroller, simply
pull out the internal strap (J2).
CLOSING THE CHASSIS WITH THE STROLLER SEAT
ATTACHED (STROLLER CONFIGURATION)
The chassis can be closed with the stroller seat attached,
both facing the parent and facing the street.
Facing the parent
fig. 58 Before closing the stroller, fold the hood, recline
the backrest to its most horizontal position, and then fully
close the stroller, as detailed above.
Facing the street
fig. 59 Before closing the stroller, fold the hood and bring
the backrest fully forward, then fully close the stroller as
detailed above.
COMFORT COVER
The All Season stroller seat is equipped with Comfort Cover