Inglesina APTICA Manuel D'instructions page 35

LIST OF COMPONENTS
fig. 1
APTICA CHASSIS
A Rear wheels
B Front wheels assembly
APTICA CARRYCOT
C Hood lining
D Carrycot apron
ALL SEASON STROLLER
E Stroller seat
F Comfort Cover
G Handrail
J Hood
ACCESSORIES
H Feeding bottle holder
K Storage basket
L Muff (if available)
M Rain cover (if available)
DARWIN INFANT / DARWIN INFANT RECLINE CAR SEAT (IF
AVAILABLE)
STANDUP (IF AVAILABLE)
CHASSIS
CHASSIS OPENING
fig. 2 Holding the lever (T1) down, lift the chassis firmly
until it opens completely.
fig. 3 Caution: ensure that all locking mechanisms
are properly engaged on both sides before use and that
none of the red indicators are visible.
ASSEMBLING/REMOVING THE REAR WHEELS
fig. 4 Insert the rear wheels (A) into the seats on the
chassis and push them until they click into place.
fig. 5 Caution: make sure that the wheels are properly
attached before use.
Should it be necessary, the rear wheels can easily be removed.
fig. 6 To remove the rear wheel (A) act on the lever (A1)
and at the same time extract it from its seat on the chassis.
REMOVING/ASSEMBLING THE FRONT WHEEL ASSEMBLY
Should it be necessary, both front wheel assemblies (B) can
easily be removed.
fig. 7 Pushing the small button (B1), pull the wheel
assembly out from its housing in the support.
fig. 8 To reinstall it, simply position it and push it until it
clicks into place.
fig. 9 Caution: make sure that the wheels are properly
attached before use.
CLOSING THE CHASSIS
fig. 10 Press the button (T2) and simultaneously rotate
the rear handle (T3) until the chassis closes completely.
Caution: always check that the chassis is closed correctly.
fig. 11 To transport the closed chassis, use the rear handle
(T3).
Never lift the chassis by the handlebar.
REAR WHEELS BRAKE
fig. 12 To operate the brake, press on the centre lever (T4).
fig. 13 To release the brake, lift the centre lever (T4).
INSTRUCTIONS
Always engage the brake during stops.
BLOCKING/UNBLOCKING THE FRONT WHEELS
The chassis features swivel wheels.
fig. 14
aligned, then operate the lever (B2) located on both front
wheel units.
ADJUSTING THE HANDLEBAR
The chassis features a telescopic handlebar, which can be
adjusted to 4 different positions.
fig. 15
raise or lower the handlebar to the desired position.
STORAGE BASKET
The chassis is equipped with a large storage basket (K), which
can be easily removed if necessary.
fig. 16
(K1) that secure it to the side tubes and detach the Velcro flap
(K2) from the rear tube (T6).
fig. 17
flap (K3) off the central brake unit.
fig. 18
respective pins (T7).
fig. 19
included), expand the front seats (K5) and at the same time
pull off the latch straps (K6) on both sides.
To reinstall the basket, carry out the above operations in
reverse.
FEEDING BOTTLE HOLDER
The chassis is equipped with a standard feeding bottle
holder (H).
fig. 20
guide in correspondence of the hook (H1) on the chassis and
push it in its housing until it is fully attached.
ADDITIONAL CARRYING UNITS FOR CHASSIS: CARRYCOT,
STROLLER SEAT AND CAR SEAT (if present)
fig. 21
the All Season stroller seat and the Darwin Infant / Darwin
Infant Recline car seat, if present.
ATTACHING THE CARRYCOT TO THE CHASSIS
fig. 22
the chassis in correspondence of the housings on both sides
of the structure and place it solely facing the parents.
fig. 23
indicators (C1) on both the attachment devices are Green.
If they are Red, reposition the carrycot correctly until the
indicators turn Green.
fig. 24
is properly attached on both sides by pulling it upwards.
DETACHING THE CARRYCOT FROM THE CHASSIS
fig. 25
and simultaneously lift it, gripping it by the handle.
FITTING THE HOOD LINING
fig. 26
it with the dedicated buttons (C3) and with the central Velcro
fastening strap (C4).
fig. 27
Velcro fastenings (C5) to the carrycot.
To lock or unlock them make sure they are correctly
Operate both buttons (T5) and simultaneously
To remove the basket, undo the 4 snap fasteners
Detach the 3 lower snap fasteners and pull the rear
Detach both footplate hooks (K4) from their
With the aid of a screwdriver or similar tool (not
To fasten the feeding bottle holder, place the upper
The chassis can be used with the Aptica carrycot,
APTICA CARRYCOT
Take the carrycot from the handle and attach it to
Once the carrycot is installed, check that the
Caution: before use, make sure that the carrycot
Operate the lever (C2) located outside the carrycot
Wrap the hood lining (C) around the handle, fixing
Complete the fitting by attaching the side and rear
35