Publicité
Liens rapides
Publicité
Manuels Connexes pour Bertazzoni MAST244GASXELP
Sommaire des Matières pour Bertazzoni MAST244GASXELP
- Page 1 BERTAZZONI INSTALLATION MANUAL FREESTANDING FULL GAS RANGES 3100427 WWW.BERTAZZONI.COM...
- Page 2 Installing the legs _____________________________________________________________ Installing the worktop frontguard ________________________________________________ Installing the island trim _______________________________________________________ Installing backguard (optional) __________________________________________________ INSTALLING THE ANTI-TIP DEVICES ______________________________________________ Anti-tip brackets ______________________________________________________________ Anti-tilt chain ________________________________________________________________ GAS CONVERSION _____________________________________________________________ INSTALLATION CHECKLIST ______________________________________________________ FINAL PREPARATION ___________________________________________________________ BERTAZZONI SERVICE _________________________________________________________...
- Page 3 / Models Models Models MAST244GASXB PROF244GASXELP MAST244GASNEE PROF244GASXE MAST244GASBIE MAST244GASXELP MAST244GASXE PROF244GASXELP PROF244GASXE...
- Page 4 / Warnings WARNINGS To ensure proper and safe operation, the applian- WARNING! ce must be properly installed and grounded by a If the information in these instructions is qualifi ed technician. DO NOT attempt to adjust, not followed exactly, a fi re or explosion may repair, service, or replace any part of your ap- result causing property damage, personal pliance unless it is specifi...
- Page 5 / Warnings Engage the range to the anti-tip device by anti-tip brackets or anti-tip chain (see installing the an- ti-tip device chapter). Ensure the anti-tip device is re-engaged when the range is moved. Re-engage the anti-tip device if the range is mo- ved.
- Page 6 / Data rating label / Before installation DATA RATING LABEL A manual valve shall be installed in an accessible The data rating label shows the model and serial location in the gas line external to the appliance number of the range. It is located under the con- for the purpose of turning on or shutting off...
- Page 7 For best removal of smoke and odors, the been designed to work in conjunction with the lower edge of the hood should be installed Bertazzoni range and have the same fi nish for a between 25 1/2” (65 cm) and 31 1/2” (80 cm) perfect look.
- Page 8 / Specifi cations Pressure Pressure Min Rate Min Rate By-pass By-pass Burner Burner Injector Injector Rate [iwc] [Btu/hr] diam.[mm] diam.[mm] Type [Btu/hr] 4’’ 3,500 1,025 Regulated Auxiliary 0.90 10’’ 3,300 0.29 0.54 LP (Propane) 4’’ 5,900 1,729 1,500 Regulated Semi-rapid 1.18 10’’...
- Page 9 / Clearence dimensions CLEARENCES DIMENSIONS Installation adjacent to kitchen cabinets Metal hood This range may be installed directly adjacent to 24’’ (60,4 cm) existing countertop high cabinets (36” or 91.5 cm 25 1/2’’(65 cm) and 31 1/2’’ (80 cm) from the fl oor). For the best look, the worktop should be level with 13’’...
- Page 10 / Installation requirements / Electrical connection INSTALLATION REQUIREMENTS ELECTRICAL CONNECTION Warning! ELECTRICAL ELECTRICAL SHOCK HAZARD A properly-grounded horizontally- mounted electri- Disconnect electrical power at the circuit bre- cal receptacle should be installed no higher than aker box or fuse box before installing the ap- 3”...
- Page 11 / Wiring diagram WIRING DIAGRAM The electric wiring diagrams and schematics are attached behind the range, and should not be removed except by a service technician, then replaced after service. COLOURS MAGNET UNITS & TERMOCOUPLES Simb. Description Green (earth) J12 J11J10 J9 J8 J7 Violet Orange J1 J2 J3 J4 J5 J6...
- Page 12 / Gas connection GAS CONNECTION Warning! FLEXIBLE CONNECTIONS DO NOT USE AN OPEN FLAME WHEN In case of installation with fl exible couplings and/ CHECKING FOR LEAKS! or quick-disconnect fi ttings, the installer must use a heavy-duty, AGA design-certifi ed commercial fl...
- Page 13 / Gas connection PRESSURE REGULATOR Since service pressure may fl uctuate with local demand, every gas cooking appliance must be equipped with a pressure regulator on the inco- ming service line for safe and effi cient operation. The pressure regulator shipped with the applian- ce has two female threads ½”...
- Page 14 / Installation INSTALLATION APPLIANCE INSTALLATION REMOVING THE OVEN DOOR Unpacking the range Prepare the door for removal. Insert the pin into • each hinge. Slowly shut the door until the protru- Remove all packing materials from the ship- ding clamps stop the movement. ping pallet but leave the adhesive-backed foam layer over brushed-metal surfaces to protect it Pull oven door upwards and remove.
- Page 15 / Installation INSTALLING THE LEGS INSTALLING THE WORKTOP FRONTGUARD Bertazzoni ranges must be used only with the legs To increase the clearance between the front edge properly installed. of the worktop and the burners, it is possible to Four height-adjustable legs are supplied with the install a front guard for the worktop.
- Page 16 / Installation INSTALLING THE ISLAND TRIM INSTALLING BACKGUARD (OPTIONAL) The island trim must be installed prior to operation The backguard must be installed prior to opera- of the appliance for appropriate ventilation of the tion of the appliance for appropriate ventilation of oven compartment.
- Page 17 / Installing the anti/tip devices INSTALLING THE ANTI/TIP DEVICES ANTI-TIP BRACKETS ANTI/TILT CHAIN The anti-tip bracket shipped with the range must The anti-tilt chain shall be installed on right or left be properly secured to the rear wall as shown in side alternatively according below instructions.
- Page 18 Replace nozzles using the conversion set sup- Save the nozzles removed from the range for fu- plied with the range or by a Bertazzoni authori- ture use. zed parts warehouse. Each nozzle has a number indicating its fl ow diameter printed on the body.
- Page 19 / Gas conversion Remove the screw located on the right side of the burner and pull out the burner from its support. ATTENTION: pay extra attention to avoid damage to the igniter and thermocouple. Step 3: oven burner (main or auxiliary) To replace the nozzles of the main oven bur- ner, start by removing the door and the bot- tom panel of the oven.
- Page 20 / Gas conversion Step 4: broiler burner primary icone are normal. The fl ame should burn completely around the bur- Remove the screw and pull out the burner from ner cap. If it doesn’t, check that the cap is posi- its support.
- Page 21 / Gas conversion For the gas valve of dual burner the choke valve is located on the valve body (fi g.20), the A screw adjust the outer ring, the B screw adjust the inner ring. OVEN BURNER Reinstall the oven door. Set the oven temperature control knob to the MA- XIMUM setting.
- Page 22 / Installation checklist / fi nal preparation INSTALLATION CHECKLIST FINAL PREPARATION • A qualifi ed installer should carry out the following Before using the oven, remove any protective checks: wrap from the stainless steel. • All stainless steel body parts should be wiped Range mounted on its legs with hot, soapy water and with a liquid stainless Island trim or Backguard attached accor-...
- Page 23 We have a dedicated team of trained professionals to answer your ne- eds. If you own a Bertazzoni appliance and need ser- vice in the US or Canada please use the following contact information: e-mail: aftersaleservice@bertazzoni.com Telephone - Monday through Friday, 7.30am to 7.30pm EST (except US public holidays).