Publicité
Les langues disponibles
Les langues disponibles
Setting up your A32 integrated amplifier
'Switch on'
state
DOWN
UP
VOLUME
Adjust
LEFT
RIGHT
BALANCE
Adjust
–dB
+dB
BASS
Adjust
–dB
+dB
TREBLE
Adjust
Customize ->
Choose
setting
Volume
VOLUME
Resolution
DISPLAY
edit
edit
STANDARD
GRAPHIC/
FINE
NUMERIC
REFERENCE
continue
Volume
Volume
resolution
display
Volume Resolution – Standard, fine
or Reference. 'Standard' and 'Fine' represent
different levels of volume control sensitivity.
The 'Reference' setting
gives
increments in 0.5dB steps.
Volume display mode – graphic or
numeric shows the volume either as a bar
graph or as a number. If Volume resolution is
set to 'Reference' a numeric volume display
shows the actual decibel figure.
Input Trims – use the source select buttons
and Control knob to set input trims for each
source. Input trims are used to compensate
for variations in output levels of different
source equipment.
All manuals and user guides at all-guides.com
INTRODUCTION
The A32 allows you to adjust listening settings
to suit your taste, and to customize various
features of the amplifier to fit your system.
Use this diagram to help you navigate through
the settings available.
The
and
ENTER
represented in the diagram by the symbols
and
respectively.
The Control knob is shown as
INPUT
TONE
TRIMS
CONTROL
edit
edit
TRIM
GLOBAL/
PER
SOURCE
continue
continue
Input
Tone
trims
control
Tone Control – Global or Per source.
This specifies the scope of changes for 'Bass'
and 'Treble' tone settings. The default setting
absolute
is 'Global' which affects all inputs equally.
'Per source' allows you to set tone controls
for individual inputs: once set, the amplifier
remembers tone settings for each input.
Processor Mode – This mode enables
you to adjust the gain of the amplifier. The
amplifier can then be used to drive the front
left and right speakers in a surround sound
system when fed from a separate processor.
You can then control the volume of the entire
system using the processor, feeding the sound
into the TAPE input. Set the gain to match the
amplifiers that drive your other loudspeakers.
ADJUSTING LISTENING
SETTINGS
The default display mode is VOLUME, where
the control knob is used to adjust sound level.
Press
through the other sound settings: BALANCE,
buttons
are
BASS and TREBLE.When a setting is selected,
SELECT
adjust it with the control knob. Press
fix the change you have made and return to
default (volume) mode, or press
.
to move to the next setting.
CUSTOMISING AMPLIFIER
SETTINGS
Press
'CUSTOMIZE->'. Now rotate the Control knob
to choose which setting you wish to alter.
Press
the Control knob.
Press
press
move on to the next item.
Press
menu.
Processor
WELCOME
mode
MESSAGE
edit
edit
GAIN
ARCAM
Amp
continue
continue
continue
Processor
Welcome
mode
message
Welcome message – You can change the power
on Welcome message from '
display your name, postcode, etc.When customising
the message, use the
select the cursor position and the Control knob to
change the letter.
Phono/Aux Text – If you have had the
optional
'Phono' so this word is displayed when the
input is selected.The default is 'Aux'.
Restore Settings – this restores all amplifier
settings, including Input trims and theWelcome
message, to their factory defaults.
9
to enter edit mode and cycle
SELECT
ENTER
SELECT
until
the
display
SELECT
to adjust the chosen setting with
SELECT
to confirm the adjustment or
ENTER
to confirm the adjustment and
SELECT
twice to leave the Customize
ENTER
RESTORE
PHONO/AUX
SETTINGS
TEXT
edit
edit
AUX/
NO/YES
PHONO
'Switch on'
state
continue
Phono/
Restore
Aux text
settings
Arcam Amp'
and
buttons to
UP
DOWN
Phono module added, choose
to
again
shows
to
Publicité
