Worx WX523 Mode D'emploi page 12

otherwise kickback may occur. lnvestigate
and take corrective action to eliminate the cause
of wheel binding.
h) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed
and carefully re-enter the cut. The wheel
may bind, walk up or kickback if the power tool is
restarted in the workpiece.
i) Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under
their own weight. Supports must be placed under
the workpiece near the line of cut and near the
edge of the workpiece on both sides of the wheel.
j) Use extra caution when making a "pocket
cut" into existing walls or other blind areas.
The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can cause
kickback.
ADDITIONAL SAFETY
RULES:
1. Always wear a dust mask.
GENERAL SAFETY
WARNINGS FOR YOUR
12
LASER
WARNING: Read all safety warnings and
all instructions. Failure to follow the
warnings and instructions may result in
serious injury.
Save all warnings and instructions for future
reference.
These lasers do not normally present an
optical hazard although staring at the beam
may cause flash blindness.
Do not stare directly at the laser beam. A
hazard may exist if you deliberately stare into
the beam, please observe all safety rules as
follows:
1) The laser shall be used and maintained
in accordance with the manufacturer's
instructions.
2) Never aim the beam at any person or an
object other than the work piece.
3) The laser beam shall not be deliberately
aimed at another person and shall be
prevented from being directed towards
the eye of a person for longer than 0.25
seconds area.
4) Always ensure the laser beam is aimed
at a sturdy work piece without reflective
surfaces, e.g. wood or rough-coated
surfaces are acceptable. Bright shiny
reflective sheet steel or similar is not suitable for
laser applications as the reflective surface may
Lithium-Ion Cordless Circular Saw
All manuals and user guides at all-guides.com
5) Do not change the laser device with
6) CAUTION: Use of controls or adjustments
ADDITIONAL SAFETY WARNING FOR CLASS
2 LASER
The laser device fitted to this tool is CLASS 2
with a maximum radiation of 1.5mW and 650nm
wavelength.
CLASS 2 LASER RADIATION, DO NOT STARE
INTO BEAM
SAFETY INSTRUCTIONS
FOR BATTERY PACK
a) Do not dismantle, open or shred cells
b) Do not short-circuit a battery pack. Do not
c) Do not expose battery pack to heat or fire.
d) Do not subject battery pack to mechanical
e) In the event of battery leaking, do not
f) Seek medical advice immediately if a cell or
g) Keep battery pack clean and dry.
h) Wipe the battery pack terminals with a
i) Battery pack needs to be charged before
j) Do not maintain battery pack on charge
k) After extended periods of storage, it may
l) Battery pack gives its best performance
m) When disposing of battery packs, keep
n) Recharge only with the charger specified
direct the laser beam back at the operator.
a different type. The manufacturer or an
authorized agent must carry out repairs.
other than those specified herein may result in
hazardous radiation exposure.
or battery pack.
store battery packs haphazardly in a box or
drawer where they may short-circuit each
other or be short-circuited by conductive
materials. When battery pack is not in use, keep
it away from other metal objects, like paper
clips, coins, keys, nails, screws or other small
metal objects, that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
Avoid storage in direct sunlight.
shock.
allow the liquid to come into contact
with the skin or eyes. If contact has been
made, wash the affected area with copious
amounts of water and seek medical advice.
battery pack has been swallowed.
clean dry cloth if they become dirty.
use. Always refer to this instruction and
use the correct charging procedure.
when not in use.
be necessary to charge and discharge
the battery pack several times to obtain
maximum performance.
when it is operated at normal room
temperature (20°C ± 5°C).
battery packs of different electrochemical
systems separate from each other.
EN