SFA Saniseat+ Notice De Service / Montage page 13

3.2.4 Electrical connection
DANGER
Connection with wet hands.
Risk of electric shock.
 Do not connect with wet hands.
• Make sure the electrical socket used is for the washing toilet seat
only and is earthed. All wiring must conform to BS7671, 1992 require-
ments for electrical installations.
• Connect the plug.
 The cistern fills up: this operation may take several seconds.
3.3 INSTALLING THE REMOTE CONTROL BRACKET
Saniseat+ is supplied with a wall bracket with double-sided adhe-
sive tape.
Stick it in the desired location, making sure that the remote control
is accessible from a seated position.
4. COMMISSIONING
Turn on the general water supply.
Press the ON/OFF button.
 The control gives a double beep.
 The POWER led lights up red.
5. OPERATION
• Switch on the washing seat by pressing the ON/OFF button.
• Certain functions become accessible.
• When you sit down, the presence sensor is activated: a double beep
sound signal confirms activation and the SITTING LED lights up. Other
functions become accessible, including washing and drying.
NOTE: It is normal to hear water flowing out even without activat-
ing the Wash function: the shower rod rinses automatically before
and after each use.
5.1 RECOMMENDATIONS FOR USE
DANGER
Splashes, sprinkling.
Risk of water infiltration into the product, short
circuit, fire starting.
Risk of unpleasant odours.
 Do not throw water on the washing seat.
 Do not urinate on the washing seat, shower
rod or air outlet.
 Do not install in a motorhome, boat or any
other unstable room.
DANGER
 Unplug the appliance in the event of prolonged absence
or thunderstorm.
DANGER
Use when all or part of the device is damaged.
Risk of water infiltration, electrocution, short cir-
cuit, fire starting.
 Unplug the device if there is:
• water leakage, damage to the device,
• noise, unusual smell of smoke being given off
by the device,
• excessively high toilet seat temperature.
DANGER
Presence of flammable products, heat
source.
Fire hazard.
Risk of plastic deformation.
 Do not throw flammable products in toilets
 Do not smoke near the product.
CAUTION
Prolonged use of the heated seat.
Risk of slight burns.
 Remain vigilant when the toilet seat is used by
a child or person with a disability.
 Do not use when drowsy or taking medication.
IMPORTANT
In case of prolonged absence, it is imperative to cut off the general
water supply and to protect the installation against frost.
Do not force the lid down.
5.2 USING THE CONTROLS
All the functions of the Saniseat+ washing toilet seat can be accessed
using the remote control.
The side control provides easy access to the main functions.
5.2.1 Buttons on the remote and side control
Buttons
Anal wash button (1st press) and massage (2d press)
1
Lets you start the anal washing function and massage function.
Vulval wash button (1st press) and massage (2d press)
2
Lets you start the vulval washing function and massage function.
Drying button
3
Lets you start drying. 4 setting levels.
Shower rod position buttons
4
Lets you move the shower rod back and forth.
Stop button
5
Lets you stop the washing, massage, drying and nozzle
cleaning functions
Water flow and drying temperature buttons
6
Lets you increase and decrease the water flow or drying
temperature.
Remote control LEDs
7
Give bright indications of settings and functions.
Water temperature button
8
Lets you adjust the water temperature. 4 setting levels.
Seat temperature button
9
Lets you adjust the seat temperature. 4 setting levels.
Nozzle cleaning button
10
Lets you start cleaning the shower rod and nozzles. Manual
or automatic activation.
11
Child mode (Preset settings.)
On/Off and Energy-saving mode button
12
Switches the device on/off/energy-saving mode, depend-
ing on short or long press.
13
Night lighting
13
1
2
3
4
5
6
STOP
7
8
9
10
11
12
13
1
2
3
5
12
EN