Ingersoll Rand 5020-EU Manuel D'instructions

TPD1360
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
FORSEEN USE
•
Series 5020T–EU and 5040T–EU Adjustable Torque
Control Impactools are designed for use in production
applications where fasteners must be applied to precise
torques. Series 5020TDQ–EU and 5040TDQ–EU
Non–Adjustable Torque Control Impactools are
designed for use in production applications where a
series of different torques must be applied to different
fasteners.
•
Ingersoll–Rand is not responsible for customer
modification of tools for applications on which
Ingersoll–Rand was not consulted.
PLACING TOOL IN SERVICE
•
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state, federal and
country), that may apply to hand held/hand operated
pneumatic tools.
•
For safety, top performance, and maximum durability
of parts, operate this tool at 90 psig (6.2 bar/620 kPa)
maximum air pressure at the inlet with 1/4" (6 mm)
inside diameter air supply hose for Series 5020–EU
Impactools or 5/16 (8 mm) inside diameter air supply
hose for Series 5040–EU Impactools.
•
Always turn off the air supply and disconnect the air
supply hose before installing, removing or adjusting any
accessory on this tool, or before performing any
maintenance on this tool.
•
Do not use damaged, frayed or deteriorated air hoses
and fittings.
•
Be sure all hoses and fittings are the correct size and
are tightly secured. See Dwg. TPD905–1 for a typical
piping arrangement.
•
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool performance, and
increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
 Ingersoll–Rand Company 2000
Printed in U.S.A.
All manuals and user guides at all-guides.com
INSTRUCTIONS FOR
SERIES 5020–EU AND 5040–EU
TORQUE CONTROL IMPACTOOLS
03539392
•
Do not lubricate tools with flammable or volatile liquids
such as kerosene, diesel or jet fuel.
•
Do not remove any labels. Replace any damaged label.
USING THE TOOL
•
Always wear eye protection when operating or
performing maintenance on this tool.
•
Always wear hearing protection when operating this
tool.
•
Keep hands, loose clothing and long hair away from
rotating end of tool.
•
Note the position of the reversing lever before operating
the tool so as to be aware of the direction of rotation
when operating the throttle.
•
Anticipate and be alert for sudden changes in motion
during start up and operation of any power tool.
•
Keep body stance balanced and firm. Do not overreach
when operating this tool. High reaction torques can
occur at or below the recommended air pressure.
•
Tool shaft may continue to rotate briefly after throttle is
released.
•
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may be
harmful to your hands and arms. Stop using any tool if
discomfort, tingling feeling or pain occurs. Seek
medical advice before resuming use.
•
Use accessories recommended by Ingersoll–Rand.
•
Use only impact sockets and accessories. Do not use
hand (chrome) sockets or accessories.
•
Impact wrenches are not torque wrenches. Connections
requiring specific torque must be checked with a torque
meter after fitting with an impact wrench.
•
This tool is not designed for working in explosive
atmospheres.
•
This tool is not insulated against electric shock.
Form P7069–EU
GB
Edition 3
July, 2000