SLV ROX ACRYL POLE 30 Mode D'emploi page 3

ENGLISH
OPERATING MANUAL FOR
OUTDOOR LUMINAIRE
ROX ACRYL POLE
Read this short manual carefully and keep it accessible for further
reference!
SAFETY MESSAGES
Disregard of the safety messages may lead to danger of life, burning or
fire!
• Installation, mounting or works on the electrical connection may only be
carried out by an approved electrician.
• The product may not be modified or converted.
• Do not hang or fasten anything on the product, especially no decoration.
• Do not cover the product - provide free air circulation.
• The foot or the base of the luminaire must be kept free and may not be
covered with dirt, leaves, etc.
• Openings providing aeration or drainage may not be covered.
• The luminaire may only be operated with a complete and intact protection
glass.
• In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
A malfunction exists when:
• visible damages appear.
• the product does not work properly (e.g. flickering).
• smoke, steam or crackling sounds appear.
• smell of burning is recognisable.
• an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
• This product is not intended to be used by children. Ensure that children do
not suffer any harm e.g. by burns from hot surfaces or by electrical shock.
Additional safety messages are indicated by this symbol:
USE AS DIRECTED
This product serves exclusively lighting purposes and may:
• only be used with a voltage of 230V ~50Hz.
• only be installed according to safety class I (one).
• only be operated when firmly mounted on a stable, even and tilt-fixed
surface.
• only be operated on normally or not flammable surfaces.
• not be exposed to strong mechanical loads or to strong contamination.
MAINTANANCE AND CARE
Light source
Exchange the light source always before it reaches its lifespan, to avoid
personal injuries, or damages of the luminaire or other objects.
Disconnect the product from the power supply, before you exchange the
light source. Let the light source cool down before replacement.
Use only light sources that are suitable for the product. Suitable light
sources are indicated on the type label.
• Suitable light sources: TC-TSE, E27, 20W max.
• Replacing the light source
• Touch energy-saving-lamps on the plastic housing, not on the bulb
glass.
• Remove the lamp head. Remove the used light source. Screw the new
light source into the socket. Put the lamp head back on. Note the proper
fit for the gasket.
• Check and clean the gasket after each opening of the luminaire. The bearing
surface of the gasket must be free of dirt. These measures ensure that the IP
class is maintained.
Care
• The following enviromental influences may have unwanted effects on the
surface of the product:
• acid rain and sour soil, high salt content in the air
• cleaning agents, fertilizer especially in flowerbeds
• thawing salt, other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface.
Disconnect the product from the power supply and let it cool down, before
you clean the product.
• Clean the product on a regular basis using a slightly moistened, soft and fluff-
free cloth. Please also note additional supplied notes on maintanance and
care.
STORAGE AND DISPOSAL
Storage
• The product must be stored in a dry and clean environment. Do not strain
the product mechanically during storage.
After a damp or soiling storage the product may only be installed after
checking its condition by an approved electrician.
Disposal (European Union)
• Do not dispose the product with the regular household waste! Products
marked with this sign must be disposed according to the directive(WEEE,
2003/108) on electrical and electronic devices at local collection points for
such devices!
INSTALLATION
(only by an approved electrician)
.
Switch off the mains or respectively the connection lead before doing any
works!
Use only parts, which are supplied with the product or are described as
accessories!
Inspect the product for loose parts inside the housing. When there are loose
parts inside the housing and these are not explicitly described the product may
not be installed or operated.
Use the supplied fastening material only when it is suited for the installation
background. If this is not the case use only fastening material suiting the
installation background.
Unpacking
• Carefully take the product out of the packaging removing any transport
safeguards.
• Before disposal of the packaging material make sure that all components of
the product are removed.
Installation place
• The product is solely suited for installation on the floor.
• The foot or the base of the luminaire must be kept free and may not be
covered with dirt, leaves, etc.
The product may only be utilized according to IP44.
IP44: Protection against foreign objects > Ø 1,0mm - Protection against
splashing water from all directions.
Choose a place where the installation is not a danger (e.g. stumbling,
knocking).
Prepare the power supply lead according to valid rules for outdoor
installations.
Do not seal the product yourself, using additional silicon or another
sealant.
Installation steps (read completely before installation)
• There are different types of mounting:
• Screw-set (Consignment): For direct mounting of the luminaire.
see figure 1.
• Earth-spike (art. no.: 229861): To fasten the luninaire in the soil, incl.
thread and nut.
see figure 2.
• Concrete anchor (SLV art. no.: 229860): For casting into liquid
concrete, including threads and nuts.
see figure 3.
• Install the luminaire as shown in the figure.
• Electrical Connection
• The product must be able to be separated by an all pole separation
from the current supply.
• Direct the connection lead through the rubber gasket.
• Direct the connection cord, in sufficient length, through the cable
screwing.
• Secure the cable screwing using a suitable tool.
• Use the second cable screwing for through-wiring.
• If you do not wire through, close the not required cable screwing with
the enclosed peg.
• Equip the three wire ends with protective tubes.
• For electric connection attach the black or brown wire (live conductor)
of the connection lead with the clamp L and the blue wire (neutral
conductor) of the connection lead with the clamp N. The green-yellow
wire (protective conductor) of the connection lead has to be tightly
screwed into the earth clamp of the product.
• Inserting the light source
• Remove the lamp head. Screw the light source into the socket. Put
the lamp head back on. Note the proper fit for the gasket.
• Fasten the luminaire on the mounting surface.
• Note the proper fit for the gasket.
Check if the product functions properly and is securely fixed!
art.-no. 232256/66/76 © 23.06.2015 SLV GmbH,
Daimlerstr. 21-23, 52531 Übach-Palenberg, Germany,
Tel. +49 (0)2451 4833-0
Technical Details are subject to change.