Publicité
1 Fastening area above the pushing handle
2 Fastening area under the device hood
Note:Observe markings for fixing points on
base frame (chain symbols).
Storage
Danger
Risk of injury and damage! Note the weight
of the appliance in case of storage.
Shutdown
Follow operating instructions of the en-
gine manufacturer!
If the sweeper is going to be out of service
for a longer time period, observe the follow-
ing points:
Park the sweeper on an even surface.
Switch off engine.
Lock parking brake.
Lock the sweeper to ensure that it does
not roll off.
Empty fuel tank.
Change engine oil.
Unscrew spark plugs and pour approx.
3 cm
of oil into the spark plug holes.
3
Crank the engine several times before
replacing the spark plug. Screw in the
spark plug.
Comfort model: Turn the push handle
lock clockwise; lock is locked.
Comfort model: Raise roller brush.
The side-brushes lift up.
Clean the inside and outside of the
sweeper.
Park the machine in a safe and dry
place.
Maintenance and care
General notes
– Maintenance work may only be carried
out by approved customer service out-
lets or experts in this field who are famil-
iar with the respective safety
regulations.
– Mobile appliances used for commercial
purposes are subject to safety inspec-
tions according to VDE 0701.
Cleaning
Caution
Risk of damage! Do not clean the appliance
with a water hose or high-pressure water jet
(danger of short circuits or other damage).
Cleaning the inside of the machine
Danger
Risk of injury! Wear dust mask and protec-
tive goggles.
Open the device hood.
Clean machine with a cloth.
Blow through machine with com-
pressed air.
Close cover.
External cleaning of the appliance
Clean the machine with a damp cloth which
has been soaked in mild detergent.
Note: Do not use aggressive cleaning
agents.
Maintenance intervals
Operating hour counter
(only Comfort model)
Note: The elapsed-time counter shows the
timing of the maintenance intervals.
Maintenance by the customer
Note: With a new motor, the oil must be
changed after the first 5 operating hours.
Daily maintenance:
Check engine oil level.
Check air filter.
Check the sweeping roller and the side
brush for wear and wrapped belts.
Check function of all operator control el-
ements.
Maintenance to be carried out every 25 op-
erating hours:
Clean air filter.
Maintenance to be carried out every 50 op-
erating hours:
Perform a motor oil change.
Check air filter, replace if extremely
dirty.
Check spark plug.
Check function of hood contact switch.
Check tension, wear and tear and func-
tioning of the drive belts and drive
chain.
Check for smooth running of the Bow-
den cables and the moveable parts
Check sealing strips at the dust filter.
Check functioning of the filter cleaning
system.
Check the sealing strips in the sweep-
ing area for position and wear.
Check the sweeping track of the sweep-
ing roller.
Check the function of the sweeping roll-
er and the side brushes.
Clean the dust filter.
Note: For description, see section on Main-
tenance work.
Note:Where maintenance is carried out by
the customer, all service and maintenance
work must be undertaken by a qualified
specialist. If required, a specialised Archer
dealer may be contacted at any time.
6
-
EN
Maintenance by Customer Service
Maintenance to be carried out after 5 oper-
ating hours:
Carry out initial inspection.
Maintenance to be carried out every 50 op-
erating hours
Maintenance to be carried out every 100
operating hours
Maintenance to be carried out every 500
operating hours
Note: In order to safeguard warranty
claims, all service and maintenance work
during the warranty period must be carried
out by the authorised Kärcher Customer
Service in accordance with the mainte-
nance booklet.
Maintenance Works
Preparation:
Park the sweeper on an even surface.
Lock parking brake.
Comfort model: Turn the push handle
lock clockwise; lock is locked.
General notes on safety
Danger
Risk of injury!
The engine requires approx. 3-4 seconds
to come to a standstill once it has been
switched off. During this time, stay well
clear of the working area.
– Allow the machine sufficient time to cool
down before carrying out any mainte-
nance and repair work.
– Do not touch any hot parts, such as the
drive motor and exhaust system.
Note: If the appliance is tilted backwards
onto the push handle, the fuel tank must not
be filled more than halfway.
Switch off the appliance prior to clean-
ing and performing any maintenance
tasks or replacing parts.
Check engine oil level and top up, if re-
quired
Danger
Risk of burns!
Allow engine to cool down.
Wait for at least 5 minutes after switch-
ing off the engine before checking the
engine oil fill level.
Open the device hood.
Unscrew and withdraw oil dipstick.
Wipe off oil dipstick and screw it in.
Unscrew and withdraw oil dipstick.
Read the value of the oil level.
– The oil level must lie between "MIN"
and "MAX" marking.
– Add motor oil if the oil level is below the
"MIN" marking.
– Do not fill oil above the "MAX" marking.
Fill motor oil into the oil fill neck.
19
Publicité
