Jennair JBZFR24IGX Guide D'utilisation Et D'entretien page 12

AUTOMATIC SETUP—WI-FI PROTECTED
SETUP (WPS)
YOU WILL NEED:
A home wireless router capable of WPS (Wi-Fi protected
Setup). The router should be on and have a live internet
connection.
To use this feature you need:
A smartphone running Android 4.3 (or higher)
with a 1280x720 (or higher) screen or a tablet or a
smartphone running iOS 8 (or higher).
A wireless router 2.4 Ghz Wi-Fi b/g/n connected to
internet (verify with your smart device that the signal
of your home wireless network is strong close to the
appliance).
The Smart Appliance Identification Number (SAID)
from your refrigerator. This is located on a sticker on
the inside of the water filter door.
SAID: 0123456789
MAC ID: 88:E7:12:XX:YY:ZZ Contains IC: 10248A-WICHIN01
NOTE: If your home wireless router is not equipped with a
WPS button, please check the user manual of your router
to confirm if it is WPS capable. If not, alternate setup
instructions are at www.jennair.com/connect.
In Canada, use jennair.ca/connected.
1.
Set up router
INTERNET
Press the WPS button on the router. An indicator light
will begin blinking.
NOTE: The WPS function on your router is active for
2 minutes. Complete the next step within that timeframe,
or you will need to reinitiate WPS.
2.
Set up refrigeration appliance (time-sensitive step)
Press and hold CONNECT on the control
panel for 3 seconds.
The Wi-Fi status indicator ( ) on the
appliance control panel will blink
slowly while your appliance and router
attempt to connect. If the connection
is successful, the Wi-Fi status indicator will illuminate
and remain lit.
12
Contains FCC ID: A5UWICHIN01
WI-FI PROTECTED
SETUP (WPS)
HOME WIRELESS
ROUTER
IF YOUR APPLIANCE DOESN'T CONNECT:
If your appliance and router fail to connect after
2 minutes, the Wi-Fi status indicator will blink rapidly
for 5 seconds and then turn off. Check any connection
instructions for your specific router, and refer to alternate
instructions at www.jennair.com/connect. In Canada,
use jennair.ca/connected.
NOTE: If this is your first smart appliance, you will need
to download the JennAir
account.
If you already have the app and a user account, please
skip ahead to Step 4, "Register your refrigerator in your
user account".
To disconnect Wi-Fi, press and the hold CONNECT for
7 to 15 seconds. The Wi-Fi status indicator will turn off,
indicating that you have disabled Wi-Fi.
To reconnect Wi-Fi, press and hold CONNECT for
3 seconds on the control panel.
The Wi-Fi status indicator ( ) on the appliance
control panel will blink slowly while your appliance
and router attempt to connect.
If the connection is successful, the Wi-Fi status
indicator will illuminate and remain lit.
DISCONNECT AND RECONNECT ROUTER
To disconnect your refrigerator from your router,
press and hold CONNECT for more than 15 seconds.
The Wi-Fi indicator will turn off, indicating that your
refrigerator is completely disconnected from Wi-Fi
and your router.
To reconnect your appliance to your router and
reconnect Wi-Fi, press and hold CONNECT for
3 seconds.
The Wi-Fi status indicator ( ) on the appliance control
panel will blink slowly while your refrigerator and router
attempt to connect.
If the connection is successful, the Wi-Fi status indicator
will come on and remain lit.
Press the WPS button on the router. An indicator light
will begin blinking.
NOTE: The WPS function on your router is active for
2 minutes. Complete the next step within that timeframe
or you will need to reinitiate WPS.
3.
Download JennAir
®
From your mobile device, smartphone, or tablet, go to
www.jennair.com/connect. In Canada, use
jennair.ca/connected. Follow the instructions to
download and install the JennAir
App and create an online user
®
App and set up user account
App.
®