Publicité
amox H10 – ET ECO S .2
Glamox H10 – ET ECO S .2
kerveiledning for Termostat
Thermostat user instructions
Explanation of programmes/modes/settings:
P1 – Lower temperature at night (night-time heating)
ttsenking
P2 – Programmes
Manual programme (works the same as when starting the radiator for the first time – Step 1)
nuell modus (Fungerer på sammen måte som ved oppstart av ovn – trinn 1
Step 1. Starting the radiator for the first time
Follow the steps below – this process is used when you start
the radiator for the first time, and to reset the radiator after a power cut.
. Start ovn for første gang!
This calibrates and resets all settings.
1. Plug the radiator in to an electric outlet
2. Turn on the radiator
gene under – denne prosessen brukes
3. Adjust the control dial
start og for å nullstille ovn etter strømbrudd.
(22°C) pointing towards the light
4. Press and hold the control dial in for 1 second until
the light blinks green
5. The radiator is now correctly set up and you can set
in kontakten
the temperature you require.
This process will reset all other settings; it is used when, for example, there has
styrehjulet med «
beena power cut or if you want to cancel the night-time heating programme.
LED indications
en er nå satt opp riktig og du kan sette ønsket temperatur.
- Idle (until ambient temperature drops).
"
"
- Heating (until ambient temperature increases).
- Knob input accepted.
"
"
- Child lock is active or heater have had power outage.
"
elvis,et strømbrudd eller du vil avslutte nattsenking (et program).
- Heater is inactive. Selected mode is not configured.
"
"
dikasjoner
- Heater is inactive. Open window detected.
"
"
"
Power cut
When a power cut occurs, the radiator will remember the settings (temperature) that were set
terinngang godkjent.
before the power cut occurred. It will start heating up again as soon as the power is on. If the temperature is
changed,the light will blink red
nesikring er aktivert eller strømtilførsel til oppvarmingsapparatet er avbrutt.
To adjust the temperature, you must follow Step 1 "Starting the radiator for the first time".If
Oppvarming er inaktiv. Oppdaget åpent vindu.
-
the radiator is turned off for a long period (e.g. during the summer), the light will blink red
when it is turned on again – follow the process for Step 1.
Resetting the radiator to factory settings
This process resets all radiator settings (programmes and services) to the factory settings so it can be set-up as new.
ed endring av temperatur vil lyset blinke rødt – indikasjon på strømstans
Factory settings
1.
Turn the control dial to the hand symbol
en av i lengre perioder (på sommeren), vil lyset blinke rødt
2.
Turn the control dial to 11°C
3. Press the control dial in for 1 second two times – The green and red lights will blink
4. Press and hold in the control dial for 3 seconds until the green light blinks
The radiator is now reset to its factory settings.
Follow the instructions in Step 1 of the instructions to set up your radiator.
nnstillinger
yrehjulet på håndsymbolet
Child safety mode
yrehjulet til 11 grader
The thermostat (control dial) can be locked to prevent children and others changing the radiator's settings and temperature.
inn styrehjulet i 1 sekund to ganger – Det grønne og røde lyset vil blinke
Activate child safety mode
og hold styrehjulet inne i 3 sekunder til det grønne lyset blinker
1.
Turn the control dial to the desired temperature (e.g. 22°C)
2.
Press and hold the control dial in for 3 seconds until the light blinks red
3. If you turn the dial at this point, the light will blink red. You cannot change the temperature.
ruksjonene i steg 1 av veiledningen for å sette opp ovnen din.
Turn off Child safety mode
1.
Turn the control dial with the arrows (show the symbols) as when turning the radiator on
2.
Press and hold the control dial in for 3 seconds until the light blinks green
3.
When the child safety mode is turned off, the radiator will heat at 22°C. Adjust to the desired temperature.
yrehjulet til ønsket temperatur (f.eks. 22 grader)
og hold styrehjulet inne i 3 sekunder til lyset blinker rødt
Adax AS, Myresgt. 1 3060 Svelvik, Norway. www.adax.no
u på hjulet nå, vil lyset blinke rødt. Du kan ikke endre temperaturen
P1 P2
P1 P2
so 2 arrows face each other
» 2 piler mot hverandre
– indicating a power outage.
– Press to confirm
– Trykk for å bekrefte
www.glamoxheating.com
You can download a complete user guide for programming
and operating the heater from www.adax.no
www.glamoxheating.com
GB
Last ned komplett m
progammering og fu
ved oppstart – følg da
2022-01-19
Art.no: 62237 Dato: 24.02.2021
7
Publicité
