Télécharger Imprimer la page

Beninca BULL 15 OMI Mode D'emploi page 21

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 40
INDEX
1) GENERAL FEATURES .................................................................................21
2)GENERAL INFORMATION ............................................................................21
3) TECHNICAL DATA ......................................................................................21
4) INSTALLATION OF THE FOUNDATION PLATE ...............................................21
5) RACK FIXING .............................................................................................22
6) LIMIT STOP FLASK POSITIONING (SEE FIG.10) ...........................................22
7) HOW TO INSTALL THE MAGNETS(BULL 15OMI.S/15OMAI.S) FIG.11 ...........22
8) MANUAL OPERATION (SEE FIG.12-13-14) ..................................................22
9) WIRE DIAGRAM .........................................................................................22
10) CP.YAK OTI CONTROL UNIT ......................................................................22
10.1) INPUT/OUTPUT FUNCTIONS ........................................................... 22
- Set the motor position by means of the menu MINV, by default the automation is set as LEFT MOTOR
- Enter the menu AUTO, confirm 2 times with <PG> and wait until the automation has carried out the autoset of the parameters
- By means of the menus PAR and LOG, select the parameters and the logic functions wanted according to the type of installation in object
IMPORTANT: After every change of the parameters FSTS. SLDO, SLDC, TSMO, TSMC, the automation executes an opening maneuver followed
by a closing one in order to acquire the new values of current and torque, on the screen will appear the message <PRG>
- To store the transmitter press the receiver button plug.
1) GENERAL FEATURES
Automation with single-phase power supply for sliding gates
2)GENERAL INFORMATION
For an efficient operation of the sliding automatic mechanism, the gate must have the following features:
- The guide rail and its wheels must be suitable in size and mantained to prevent gate from excessive sliding friction.
- When running, gate must not rock excessively.
- Opening and closing stroke must be regulated by a mechanical limit stop (to safety standard in force).
3) TECHNICAL DATA
Feed
Absorption
Torque
Inverter
Operating jogging
Protection degree
Working temperature
Max. gate weight
Rack modulus
Opening speed
Noise level
Lubrication
Weight
* RMS value
** M6 Z13 (art. RI.P6 - optional)
4) INSTALLATION OF THE FOUNDATION PLATE
Dimensions of the foundation plate are shown in Fig. 2.
It is essential to keep the distance from the rack, in order to position and remove the actuator once the rack is fitted to the gate leaf.
The types of fittings of the foundation plate are mainly the following:
1 Installation without adjustment in height on the already existing base in concrete (Fig.2).
By using the plate as drilling template, drill 4 holes Ø10mm, and insert the steel threaded screw anchors, Ø10x120mm, similar to those shown in Fig. 2.
Lock the actuator directly to floor, as indicated in Fig.7.
QUICK PROGRAMMING
BULL 15 OMI
230Vac 50/60Hz
2 A*
50 Nm
Yes
40%
IP44
-20°C / +50°C
1500 kg
M4 Z 18**
24 m/min MAX
<70 dB
Oil
21,3 kg
10.2) HOW TO CHECK CONNECTIONS ..................................................... 23
11) PROGRAMMING ......................................................................................23
12) TO ACCESS PROGRAMMING ....................................................................23
12.1) RUN SELF-LEARNING AND ANTI-CRUSHING DEVICE SETTING ........ 23
13) PARAMETERS, LOGIC AND SPECIAL FUNCTIONS .....................................24
14) HOW TO ADJUST SPEED AND BRAKING ...................................................26
15) AUTOSET ................................................................................................27
16) ERROR MESSAGES .................................................................................28
17) DISPLAY LCD ..........................................................................................28
18) DIAGNOSTICS .........................................................................................28
19) MAINTENANCE ........................................................................................29
BULL 15 OMAI
115Vac 60Hz
2 A*
50 Nm
Yes
40%
IP44
-20°C / +50°C
1500 kg
M4 Z 18**
24 m/min MAX
<70 dB
Oil
21,3 kg
21

Publicité

loading

Ce manuel est également adapté pour:

Bull 15 omai