Publicité
Les langues disponibles
Les langues disponibles
itch action
ction
Switch action
Switch action
Switch action
Switch action
CAUTION: Before installing the battery pack into the tool,
always check to see that the switch trigger actuates properly and
returns to the "OFF" position when released.
To start the tool, simply pull the switch trigger. Tool speed is
increased by increasing pressure on the switch trigger. Release
the switch trigger to stop.
on
witch action
ng switch action
versing switch action
action
Reversing switch action
Reversing switch action
Reversing switch action
Reversing switch action
CAUTION: Always check the direction of rotation before
operation.
CAUTION: Use the reversing switch only after the tool comes
to a complete stop. Changing the direction of rotation before the tool
stops may damage the tool.
differ
CAUTION: When not operating the tool,always set the
reversing switch lever to the neutral position.
witch to change the direction of rotation. Depress the reversing switch lever
has a reversing switch to change the direction of rotation. Depress the reversing switch lever
reversing switch to change the direction of rotation. Depress the reversing switch lever
s tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever
ing switch to change the direction of rotation. Depress the reversing switch lever
This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever
This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever
This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever
This tool has a reversing switch to change the direction of rotation. Depress the reversing switch le
m the A side for clockwise rotation or from the B side for counterclockwise rotation.
ockwise rotation or from the B side for counterclockwise rotation.
A side for clockwise rotation or from the B side for counterclockwise rotation.
e rotation or from the B side for counterclockwise rotation.
for clockwise rotation or from the B side for counterclockwise rotation.
from the A side for clockwise rotation or from the B side for counterclockwise rotation.
from the A side for clockwise rotation or from the B side for counterclockwise rotation.
from the A side for clockwise rotation or from the B side for counterclockwise rotation.
from the A side for clockwise rotation or from the B side for counterclockwise rotation.
e reversing switch lever is in the neutral position,the switch trigger cannot be pulled.
lever is in the neutral position,the switch trigger cannot be pulled.
en the reversing switch lever is in the neutral position,the switch trigger cannot be pulled.
sing switch lever is in the neutral position,the switch trigger cannot be pulled.
witch lever is in the neutral position,the switch trigger cannot be pulled.
When the reversing switch lever is in the neutral position,the switch trigger cannot be pulled.
When the reversing switch lever is in the neutral position,the switch trigger cannot be pulled.
When the reversing switch lever is in the neutral position,the switch trigger cannot be pulled.
When the reversing switch lever is in the neutral position,the switch trigger cannot be pulled.
p
e front lamp
hting up the front lamp
t lamp
up the front lamp
Lighting up the front lamp
Lighting up the front lamp
Lighting up the front lamp
Lighting up the front lamp
CAUTION: Do not look in the light or see the source of light
directly.
Pull the switch trigger to light up the lamp. The lamp keeps on
lighting while the switch trigger is being pulled. The lamp goes
s the
out approximately 10 seconds after releasing the switch trigger
ther
ge
change
eed change
Speed change
Speed change
Speed change
Speed change
CAUTION: Always set the speed change lever fully to the
correct position. If you operate the tool with the speed change
lever positioned halfway between the "1" side and "2" side, the
tool may be damaged.
era-
CAUTION: Do not use the speed change lever while the tool
the
is running. The tool may be damaged.
Displayed Number
1
2
Speed
Torque
Applicable operation
Low
High
Heavy loading operation
High
Low
Light loading operation
- 07 -
To change the speed, switc
To change the speed,
To change the s
To change
speed or "1" for low speed b
speed or "1" for low sp
speed or "1" for
speed or "
position before operation.
position before operat
position before o
position be
If the tool speed is coming
If the tool speed is co
If the tool speed
If the tool
display "1" and restart the op
display "1" and restart
display "1" and r
display "1"
Cleaning / Maintenan
Cleaning / Mainte
Cleaning / M
Cleanin
Cleaning
Cleaning
Cleaning
Cleaning
This device complies with
This device complies
This device com
This devic
conditions:
conditions:
conditions:
conditions
(1) This device may not caus
(1) This device may no
(1) This device m
(1) This de
received, including interferen
received, including inte
received, includi
received, i
To c
spee
posi
If the
disp
Cle
Clea
This
cond
(1) T
rece
Publicité
