Publicité
Note
Base selection of drive rolls upon the following recommended usages:
1
2
3
4
5
Wire Diameter
Fraction
.023/.025 in.
.030 in.
.035 in.
.045 in.
.052 in.
1/16 in.
Item
Dia.
Part
No.
Mkgs.
No.
. . .
1
. . . . . . . . . . .
148 809
. . .
2
. . .
FM1
. . .
188 706
. . .
3
. . . . . . . . . . .
188 709
. . .
4
. . .
GS1
. . .
125 785
. . .
5
. . . . . . . . . . .
143 810
. . .
6
. . . . . . . . . . .
169 654
. . .
7
. . . . . . . . . . .
188 441
. . .
8
. . . . . . . . . . .
605 227
. . .
9
. . . . . . . . . . .
178 126
.
La visserie est seulement disponible
que si elle figure sur la liste.
1
To maintain the factory original performance of your equipment, use only Manufacturer's Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM–1319 Page 24
Table 6-1. Drive Roll And Wire Guide Kits
V-Grooved rolls for hard wire.
U-Grooved rolls for soft and soft shelled cored wires.
U-Cogged rolls for extremely soft shelled wires (usually hard surfacing types).
V-Knurled rolls for hard shelled cored wires.
Drive roll types may be mixed to suit particular requirements (example: V-Knurled roll in combination
with U-Grooved).
Decimal
Metric
.023/.025 in.
0.6 mm
.030 in.
0.8 mm
.035 in.
0.9 mm
.045 in.
1.2 mm
.052
1.3 mm
.062
1.6 mm
Description
Figure 6-5. Panel, Rear w/Components (Fig 6-1 Item 3)
. . .
BLADE, fan 9 in 5wg 34deg .309 bore CCW
. . .
MOTOR, fan 230V 50/60 Hz 1550RPM .312dia shaft
. . .
WINDTUNNEL, 9 in
. . .
VALVE, 24VAC 2 way custom port 1/8 orf
. . .
PANEL, rear
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . .
BRACKET, support tank
. . .
CHAIN, weldless 2/0 x 31.000 lg
. . .
NUT, nyl hex jam .750NPST
. . .
CONNECTOR, clamp cable .690/1.070
5
4
3
2
Figure 6-5. Panel, Rear w/Components
Drive Roll
Kit No.
Part No.
087 131
087 130
079 594
053 695
079 595
053 700
079 596
053 697
079 597
053 698
079 598
053 699
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
8
9
Inlet
Wire Guide
Type
V-Grooved
056 192
V-Grooved
056 192
V-Grooved
056 192
V-Grooved
056 193
V-Grooved
056 193
V-Grooved
056 195
Ref. S-0026-B/7-91
. . . . . . . . . . . . . . . . . . .
7
Ref. ST-802 088-A
Quantity
1
1
1
1
1
1
1
1
1
Publicité
