Set-Up And Operation; Safety Features; Cleaning And Maintenance; Ce-Statement - EUROM CK1500 Manuel D'utilisation

Set-up and Operation


Make sure the heater is turned off and that the thermostat dial is set to maximum (clockwise, as far as it will
go). Now plug into an earthed, correctly functioning 220-240V / 50Hz socket. Only connect the heater to an
earthed socket!

In order to switch on the heater, set one or both mode selector dials to 650W. c.q. 850W. The light(s) on the
related switch(es) turn(s) on and the heater starts to function. For slow heating, a small rise in temperature
or a small space, choose setting 650W. For quick heating, a bigger temperature rise or a larger space,
choose setting 850W. 650W and 850W together give full power: 1500W.

When the space has reached the desired temperature, turn the thermostat dial anticlockwise slowly until you
hear a click. In this position, the thermostat will maintain the current temperature by turning the heater on
and off for a top-up, if necessary. If so desired, you can now switch to a lower power level. For higher
temperatures, turn the thermostat dial clockwise, for lower temperatures anticlockwise.

To switch off, click the mode selector dial to off. The heater switches off, the pilot light will turn off. Unplug.

Safety features

In case of internal overheating, the overheating safeguard will switch the heater off. This may occur if the heater
cannot give off enough heat or if it cannot draw in enough fresh air. As mentioned above, this is generally caused
by (partially) covering the heater, obstructing the air intake and/or outlet grills or installing the heater too close to a
wall or something similar. In case of overheating, switch off the heater and unplug. Give the heater time to cool
down, remove the source of the overheating and use as normal. If the problem persists or if you have not been
able to trace the source of the overheating, turn the heater off immediately and unplug. Contact a servicing point
to have the heater repaired.

Cleaning and Maintenance

Keep the heater clean. Deposits of dust and dirt in the appliance are a common cause of overheating so these
should be removed regularly. Switch off the heater, remove the plug from the socket and allow the heater to cool
down before cleaning or carrying out maintenance work.

Wipe the outside of the heater regularly with a dry or slightly damp cloth. Do not use aggressive soaps,
sprays, cleaners or abrasives, waxes, polishes or chemical solutions!

Use a vacuum cleaner to carefully remove any dust and dirt from the grills and ensure that the air intake and
outlet openings are clean. Be careful not to touch or damage any internal parts during cleaning!

The heater contains no other parts which need maintenance.

At the end of the season, store the cleaned heater in the original packaging if possible. Store it upright in a
cool, dry and dust-free place.

Do not dispose of heater with household waste when it becomes worn or damaged beyond repair. Take it to
your local authority's collection point for electrical appliances where any reusable materials will be collected
and redistributed.

CE-statement

Euromac bv, Genemuiden-NL hereby declares that the EUROM electrical convector heater, type CK1500,
complies with the LVD guideline 2006/95/EG and the EMC guideline 2004/108/EC and meets the following
standards:
EN 60335-1:2012
EN 60335-2-30:2009+A11:2012
EN 62233:2008
Genemuiden, 04-08-2014
W.J. Bakker, alg.dir.
EN 55014-1:2006/+A1:2009/+A2:2011
EN55014-2:1997/+A1:2001/+A2:2008
EN 61000-3-2:2006/+A1:2009/+A2:2009
EN 61000-3-3:2008
11