Publicité
Les langues disponibles
Les langues disponibles
Cool Down Period
For best performance, allow 4 hours for the Beverage Center to cool down completely. The
Beverage Center will run continuously for the first several hours.
Temperature Control
Indication of Temperature in Lower Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
Indication of Temperature in Lower Chamber
Indication of Temperature in Upper Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature increase 1°C.
Press this button once to increase temperature 1° F/C.
: Press this button once and the temperature decrease 1°C.
: Press this button once and the temperature decrease 1°C.
Press this button once to decrease temperature 1° F/C.
Indication of Temperature in Upper Chamber
The Beverage Center can be operated by adjusting the temperature control buttons (up arrow
: Temperature display.
and down arrow) until the desired temperature is reached.
: Press this button once and the temperature increase 1°C.
The display will flash for a few seconds before set point is locked in.
Light: Lighting button for LED lamp; it controls the on/off of lamp.
: Press this button once and the temperature decrease 1°C.
The temperature range MIN and MAX is 33° - 50°F (1° - 10° C).
Power: On/off button used to turn on/off all load.
Press Light and Power together for 2 seconds and you can convert betwee
Temperature display
: Temperature display.
fahrenheit temperature and Celsius temperature.
Light: This button turns the light ON and OFF.
Light: Lighting button for LED lamp; it controls the on/off of lamp.
Power: This buttons turns the power ON and OFF.
Power: On/off button used to turn on/off all load.
Notice!
Press both Light and Power button's at the same time to change between Fahrenheit and
Celsius temperatures.
Press Light and Power together for 2 seconds and you can conve
The default temperature is 10/10°C, and the temperature after powe
fahrenheit temperature and Celsius temperature.
• The default temperature for the Beverage Center is 54°F (12°C). The temperature after
failure will be the temperature set before the power failure.
power failure will be the temperature set before the power failure.
To elongate the service life of compressor, please wait for at least
• To prolong the life of compressor, please wait for at least 5 minutes before the Beverage
Center is restarted after power failure.
Notice!
minutes before the wine cooler is restarted after power failure.
Failure display
The default temperature is 10/10°C, and the temperature a
• If "E" and "F" are displayed, please contact local service personnel for repair.
Failure display
failure will be the temperature set before the power failure.
• If the temperature in the cooler is too low, it will display "L".
If there is failure on the sensor, the screen may display failure code, suc
• If the temperature in the cooler is too high, the screen will display "H" and will flash. Under
To elongate the service life of compressor, please wait for
this state, the buzzer will buzz for 30 seconds. One minute later, the buzzer will continue to
as: E and F. When the screen displays the above-mentioned errors, pleas
buzz for the next 30 seconds. After three times, the alarm will not buzz any more. You can
press any key to cancel sound alarm.
minutes before the wine cooler is restarted after power failure.
do not disassemble it for check by yourself. You should contact loca
• Storing too many wine bottles in the cooler may cause the temperature in the cooler to rise
temporarily.
Failure display
after-sales service personnel for repair.
If there is failure on the sensor, the screen may display failure c
If the temperature in the cooler is too low, it will display "L".
as: E and F. When the screen displays the above-mentioned erro
When the temperature in the cooler is too high, the screen will display "H
do not disassemble it for check by yourself. You should co
and will flash; under this state, the buzzer will buzz until 30 seconds; on
CONTROLS AND SETTINGS
7
Publicité
