Scheppach MR760-E Traduction Des Instructions D'origine page 41

9.1 Inserting / removing the mulching insert (Fig.
9.1; 9.2; 9.3)
Depending on the assignment, you can choose be-
tween mowing with the mulching insert (38) and mow-
ing with the side discharge (11) open.
1. Pull the side discharge locking pin (24) upwards and
lift the side discharge (11).
2. The side discharge opening (e) can be found here.
3. Now hook the mulching insert (38) into the eyelets
provided on the mowing unit using the hooks on
the mulching insert.
4. Now fold the side discharge (11) down again.
5. In order to mow with the side discharge (11) open,
unhook the mulching insert (38) as described
above.
9.2 Checking the tyre pressure
The correct tyre pressure is the essential prerequisite
for a perfectly balanced cutting tool and thus also for
an evenly mown lawn.
1. Check the tyre pressure with a commercially avail-
able foot pump at regular intervals.
2. If necessary, refill with air using a commercially
available foot pump (not included in scope of de-
livery). The correct tyre pressure is 2.7 bar in the
front wheels (7) and 1.9 bar in the rear wheels (5).
Note: If you notice that the tyres or wheels are dam-
aged, please contact the customer service or a spe-
cialist workshop.
9.3 Checking the seat contact switch (fig. 1)
The seat contact switch ensures that the motor switch-
es off as soon as there is no one in the driver's seat.
1. Sit on the driver's seat (2).
2. Depress the brake pedal (8) and activate the lock-
ing brake (14).
3. Activate the mower by inserting the ignition key
(30) into the ignition lock (23). Set the key to "ON".
4. Switch the mowing unit (6) on by pulling the mower on/
off knob (17) up.
5. Take the weight off the driver's seat (2) by stand-
ing up (do not get off!)
6. The engine must switch off!
Note: If you notice that the contact switch is not work-
ing correctly, please contact the customer service or a
specialist workshop.
9.4 Adjusting the correct seat position (Fig. 8)
1. Sit on the driver's seat (2).
2. Pull the seat adjustment lever (12) upwards and
hold it in this position.
3. You can now correct the seat by moving it for-
wards or backwards.
4. Adjust the seat position so that you sit safely and
comfortably and can easily reach the controls.
10. Control panel functions
(Fig. 12, Fig. 1)
c WARNING!
Familiarise yourself with the functions of the mower
before using it.
10.1 USB sockets (16)
The control panel has two USB sockets.
1. Connect your phone to the USB socket using a
USB cable (not included in the scope of delivery),
for example.
2. Stow your phone safely in your pants pocket and
ensure that the cable does not sag.
10.2 Mowing unit on/off (17)
1. Switch the mowing unit on by pulling the mowing
unit on/off switch (17) up.
2. Switch the mowing unit off by pushing the switch
down.
3. The mowing unit switches off automatically if revers-
ing without the reverse mowing option (20) active.
4. In this case, the mowing unit switch (17) must be
pushed down and can subsequently be reactivat-
ed again by pulling it up.
10.3 Charge status display (18)
The charge status display shows you the charge sta-
tus in 5 levels:
0 % 25 %
10.4 Operating hours indicator (19)
The operating hours indicator shows you how many hours
the battery-powered ride-on lawnmower was previously in
operation for.
10.5 Reverse mowing option (20)
c WARNING!
Only use this option when the terrain does not permit
mowing moving forwards!
1. Press the "Reverse mowing option on/off" button
(20). An LED illuminates.
2. Switch the mowing unit (6) on by pulling the mow-
ing unit on/off switch (17) up.
3. You can now also mow in reverse.
10.6 Cruise control (22)
Cruise control is used to relieve the legs and keep a
constant speed.
10.6.1 Cruise control with the mowing unit
switched on
1. Switch the mowing unit on as described in point
11.6.2 and drive carefully as described there.
2. Press the "Cruise control on/off" switch (22).
www.scheppach.com
50 % 75 % 100 %
GB | 41