3M PELTOR WS ALERT XPI MRX21AWS6 Serie Mode D'emploi page 9

NOTE:
• When worn according to the User Instructions, this hearing
protector helps reduce exposure to both continuous noises,
such as industrial noises and noises from vehicles and
aircraft, as well as very loud impulse noises. It is difficult to
predict the required and/or actual hearing protection
obtained during exposure to impulse noises. Proper
selection, fit and use of hearing protection, proper care of
hearing protection, and other variables will impact
performance. To learn more about hearing protection for
impulse noise, visit www.3M.com/PELTOR
• This earmuff is provided with level-dependent attenuation.
The wearer should check correct operation before use. If
distortion or failure is detected, the wearer should refer to
the manufacturer's advice for maintenance and replacement
of the battery.
• This hearing protector limits the entertainment audio signal
to 82 dBA effective to the ear.
• Operating temperature range: -20°C (-4°F) to 55°C (131°F)
• Storage temperature range: -20°C (-4°F) to 55°C (131°F)
• This product contains electrical and electronic
components and must not be disposed of using standard
refuse collection. Please consult local directives for disposal
of electrical and electronic equipment.
APPROVALS
Hereby, 3M Svenska AB declares that the radio equipment
type Radiobroadcast receiver is in compliance with Directive
2014/53/EU and other appropriate directives to fulfill the
requirements for the CE marking. The full text of the EU
declaration of conformity is available at the following internet
address: www.3M.com/PELTOR/DOC
Upon request, type in your part number. The part number of
your earmuffs can be found at the bottom of one cup as seen
in the picture below.
A copy of the declaration of conformity and additional
information required in the directives can also be obtained by
contacting 3M in the country of purchase. For contact
information, see last pages of this user instruction.
The product has been tested and approved in accordance
with EN 352-1:2002 / EN 352-3:2002, EN 352-4:2001 /
A1:2005, EN 352-6:2002, EN 352-8:2008. Notified Body
Statement of Opinion offered by: FIOH, Finnish Institute of
Occupational Health, Topeliuksenkatu 41 B, FI-00250,
Helsinki, Finland. Notified body #0403.
LABORATORY ATTENUATION
WARNING! 3M strongly recommends individual fit testing
of hearing protectors. If the SNR is used to estimate
typical workplace protection, 3M recommends that the
noise reduction value be reduced by 50% or in
accordance with applicable regulations.
Explanation of attenuation tables
EN 352-1/EN 352-3/EN 352-4
A:1 Frequency (Hz)
A:2 Mean attenuation (dB)
A:3 Standard deviation (dB)
A:4 Assumed protection value, APV (dB)
A:5
H = Hearing protection estimation for high frequency
sounds (ƒ ≥ 2000Hz).
M = Hearing protection estimation for medium frequency
sounds (500Hz < ƒ < 2000Hz).
L = Hearing protection estimation for low frequency
sounds (ƒ ≤ 500Hz).
A:6 Criterion Level
H = Criterion level for high-frequency noise
M = Criterion level for medium-frequency noise
L = Criterion level for low-frequency noise
Compatible Industrial Safety Helmets EN 352-3
These earmuffs should be fitted to and used only with, the
industrial safety helmets listed in Table B. These earmuffs
were tested in combination with the following industrial safety
helmets and may give different levels of protection if fitted to
different helmets.
Explanation of the industrial safety helmet attachment table:
B:1 Helmet manufacturer
B:2 Helmet model
B:3 Attachment
B:4 Head size: S = small, M = medium, L = large
Headband MRX21AWS6*
D:1 Headband (PVC, PA)
D:2 Headband wire (stainless steel)
D:3 Two-point fastener (POM)
D:4 Cushion (PVC foil and PUR foam)
D:5 Foam liner (PUR foam)
D:6 Cup (ABS)
D:7 Level-dependent microphone for ambient listening
(PUR foam)
D:8 Speech microphone (ABS, PA)
D:9 Antenna (PE, ABS, TPE)
D:10 Wind shield (foam)
D:11 Charger jack (stainless steel)
Helmet attachment/Hardhat MRX21P3EWS6*
D:12 Cup supporting arm (stainless steel)
GB
2