G Eneral Notes On Safety; Se Of The Machine For Purposes For Which It Is Intended; I Ncorrect Use; Ec Declaration Of Conformity - SUHNER ABRASIVE UWG 10-R125 Dossier Technique

1. n
1.1 g
enerAl notes on sAfety
This operation manual is applicable for the machine UWG
10-R125. The machine may only be handled by personnel
who are qualified.
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may con-
tact hidden wiring or its own cord. Contact with a «live»
wire will make exposed metal parts of the tool «live» and
shock the operator.
WARNING Read all safety warnings and all in-
structions. Failure to follow the warnings and in-
structions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
1.2 u
se of the mAchine for purposes for
which it is intended
The machine is intended for the purpose of cutting, rough-
ing and brushing of metal and stone materials without the
use of water.
1.3 i
ncorrect use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 ec
declArAtion of conformity
Otto Suhner GmbH of Trottäcker 50, D-79701 Bad Säck-
ingen, hereby declares under sole responsibility that the
product with the serial or batch no. (see reverse side) com-
plies with the requirements under the Directive 2014/30/
EU, 2006/42/EC, 2011/65/EU. Applied standards: EN ISO
12100, EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-
2, EN 61000-3-3. Document Agent: M. Voyame. D-Bad
Säckingen, 01/2019.
M. Voyame/Managing Director
2. c
2.1 p
rior to tAKing the mAchine into serVice
Before connecting tool to a power
source, be sure the voltage sup-
plied is the same as specified on
the name plate of the tool.
The power supply should not vary more than 10% above
or below the voltage indicated on the nameplate.
Check grinding tool prior to use. The grinding tool must
be mounted centrally and positioned against the limit
stop. The maximum allowable speed of the tool and of the
24
S
oteS on afety
ommISSIonIng
chuck may not be exceeded under any circumstances.
Observe national regulations. Fit hand protection. Take
protective measures when dust can develop during work-
ing that is harmful to one's health, cumbustible or explo-
sive. Wear a dust mask and work with dust/chip extraction
when connectable.
2.2 t
AKing the mAchine into serVice
Preselect speed with adjusting wheel according to speed
table.
Level 1: 4200min
-1
Level 2: 5200min
-1
Level 3: 6400min
-1
During operation never exceed the speed which
has been matched to the grinding tool specifica-
tions!
2.2.1 t /t
urn on urn off
The switch must be at the OFF position, i.e. the «0» is
visible. To switch ON the tool, press the switch, and push
it forwards until it engages audibly, i.e. the «1» becomes
bisible. Press the ON/OFF swith to trigger the blocking
and the machine shuts down.
2.3 r

Ating dAtA

Power voltage
Power Input
Power Output
No-load speed
Max. tool Ø
Grinding spindle thread
Sound pressure level EN 60745
Noise emission level
Level 4: 7600min
-1
Level 5: 8800min
-1
Level 6: 10000min
-1
120/230/240V, 50/60Hz
1050W
650W
10500min
-1
125mm
M14 / 5/8"-11
84dB(A), K=3dB
95dB(A), K=3dB