Before Starting The Machine; Setting The Cutting Height; Fuel And Oil; Operation - Royal RBC 41 Mode D'emploi D'origine

Anleitung_RBC_41_SPK7:_
GB
Important:
Do not remove the screws in the mount for fastening
the guard hoods. These screws must remain on the
equipment.
5.4 Fitting / Replacing the line spool
Line up the hole in the carrier plate with the notch
beneath it and lock the carrier plate with the size 6
Allen key (Fig. F4)
Secure the line spool on to the locating pin (Fig. F5).
Important: Left-hand thread!
To dismantle, proceed in reverse order.
5.5 Mounting the blade guard hood
Important: The cutting blade guard hood must be
fitted if you wish to work with the cutting blade. The
guard hood for the cutting blade must be installed as
shown in Figures F7 – F9.
Important:
Do not remove the screws in the mount for fastening
the guard hoods. These screws must remain on the
equipment.

6. Before starting the machine

Check that all moving parts move smoothly before
you start using the machine. Check that all screw
connections are securely fastened and also check all
the safety devices.

6.1 Setting the cutting height

Fit the carrying strap as shown in Figures G1 –
G3.
Hook the machine to the carrying belt (Fig. G4).
Adjust the perfect working and cutting position
using the various strap adjusters on the carrying
strap (Fig. G5).
In order to establish the optimum length of the
carrying strap, you should then make a few
swinging movements without starting the engine
(Fig. H).
The carrying strap is fitted with a quick-release
mechanism. Pull the red strap section (Fig. G6) if you
need to remove the strap quickly.
Important: Always use the strap when working with
the machine. Attach the strap as soon as you have
started the engine and it is running in idle mode.
Switch off the engine before you take off the carrying
strap.
20
01.02.2010 16:06 Uhr Seite 20
Check the machine for the following each time before
use:
That there are no leaks in the fuel system
That the cutting unit and all safety devices are in
perfect condition
That all screws are securely fastened

6.2 Fuel and oil

Recommended fuels
Use only a mixture of normal unleaded petrol and
special 2-stroke engine oil. Mix the fuel mixture as
indicated on the fuel mixing table.
Please note: Do not use a fuel mixture which has
been kept for longer than 90 days.
Please note: Do not use 2-stroke oil with a
recommended mixing ration of 100:1. If inadequate
lubrication causes engine damage, the
manufacturer's engine warranty will be voided.
Please note: Only use containers designed and
approved for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke oil
into the mixing bottle (see scale printed on the bottle).
Then shake the bottle well.
6.3 Fuel mixture table
Mixing procedure: 25 parts petrol to 1 part oil
1 liters
2 liters

7. Operation

Please note that the statutory regulations governing
noise abatement may differ from town to town.
7.1 Starting the engine when cold
Fill the tank with the required amount of oil/petrol mix.
See "Fuel and oil".
1. Set the machine down on a hard, level surface.
2. Set the choke lever (Fig. A/Item 10) to "
3. Press the fuel pump (primer) (Fig. A/Item 16) 10
times.
4. Switch the ON/OFF switch (Fig. A/Item 6) to "I".
5. Secure the throttle lever. To do so, actuate the
throttle lock (Fig. A/Item 7) and then actuate the
throttle lever (Fig. A/Item 8) while pressing the
locking button (Fig. A/Item 9) at the same time to
secure the throttle lever.
6. Hold the machine firmly and pull out the starter
cable (Fig. A/Item 11) until you feel it start to
resist. Then tug sharply on the starter cable 4
times. The machine should start.
Petrol 2-stroke oil
40 ml
200 ml
".