Technical Data - Royal RBC 41 Mode D'emploi D'origine

Anleitung_RBC_41_SPK7:_

4. Technical data

Engine type
2-stroke engine, air-cooled, chrome cylinder
Engine power (max.)
Displacement
Idle speed of engine
Max. engine speed
Scythe
Trimmer
Max. speed (cutting speed)
Scythe:
Trimmer:
Ignition
Drive
Weight (with empty tank) Scythe/Trimmer 7.0/7.2 kg
Long handle length
Cutting circle diameter of line
Cutting circle diameter of blade
Cutting line length
Cutting line diameter:
Tank capacity
Spark plug NGK BPMR7A / Champion RCJ6Y
Petrol consumption (in accordance with ISO 8893)
at max. engine power
Specific fuel consumption (in accordance
with ISO 8893) at max. engine power
Vibration a
h,w
Trimmer
Scythe
K uncertainty
L sound pressure level
pA
Idling speed (max.)
In operation (max.)
K uncertainty
L sound power level
WA
Idling speed (max.)
In operation (max.)
K uncertainty
01.02.2010 16:06 Uhr Seite 19
5. Installation
Open the packaging and take out the gardening
equipment with care.
Remove the packaging material and any
packaging and/or transportation braces (if
1.4 kW/1.9 hp
available).
40.6 cm 3
Check that all items are present.
2800 +/- 200 rpm Inspect the equipment and accessories for
damage in transit.
If possible, keep the packaging until the end of
9,000 rpm
the guarantee period. Please dispose of the
packaging in an environment-friendly fashion
8,400 rpm
within the scope of a recycling system.
6750 rpm
IMPORTANT
The equipment and packaging material are not
6300 rpm
toys. Do not let children play with plastic bags,
Electronic
foils or small parts. There is a danger of
Centrifugal clutch
swallowing or suffocating!
5.1 Installing the long handle
150 cm
Install the long handle as shown in Figures D1 – D3.
Ø 41 cm
Do not tighten the screws until you have set the
perfect working position with the carrying strap. The
Ø 23 cm
long handle should be aligned as shown in Figure A.
8.0 m
2.0 mm 5.2 Fitting / Replacing the blade (Fig. E1 – E3)
When the machine is supplied the blade is ready-
0.8 l
fitted. Therefore we will first explain how to remove it.
Line up the hole in the carrier plate (Fig. E1/ Item
25) with the notch beneath it and lock the carrier
plate with the size 6 Allen key (Fig. E1/E2)
0.8 kg/h
Remove the securing nut for the blade using the
supplied spark plug wrench (Fig. E2). Important:
Left-hand thread!
457 g/kWh
Remove the pressure plate cover (Fig. E3/Item
26) and the pressure plate (Fig. E3/Item 27)
6.45 m/s 2
The blade (Fig. E3/Item 4) can now be removed.
To assemble, proceed in reverse order. Please
7.15 m/s 2
note that the side of the pressure plate (Fig.
1.5 m/s 2
E3/Item 27) with the recess must point towards
the blade.
84 dB (A)
5.3 Installing the cutting line guard hood
104 dB (A)
Important: The cutting line guard hood must be fitted
1.5 dB (A)
if you wish to work with the cutting line.
The guard hood for the cutting line must be installed
as shown in Figures F1 – F3.
102 dB (A)
A blade (Fig. F6/ Item A) on the underside of the
114 dB (A) guard hood automatically cuts the cutting line to the
optimum length. This is covered by a guard (Fig.
1.5 dB (A)
F6/Item B).
Remove the guard before you start working and
replace it when you have finished working.
GB
19