Publicité
Les langues disponibles
Les langues disponibles
Start-up
The two vacuum tubes are now firmly connected
together. They are not intended to be detached
from each other again.
Opening the intake grille of the appliance (06)
1. Hold the appliance (06/1) tight.
2. Firmly slide the screwdriver (06/2) of the
spark plug spanner into the upper lateral
opening (06/3) of the intake grille (06/4).
NOTE
Do not slide the screwdriver into the front
lateral opening to which the arrow (that is
mounted on the vacuum grille) points.
3. Push the inserted screwdriver, together with
the intake grille, away from the appliance.
The intake grille swivels up.
Connecting the upper vacuum tube to the
appliance (07)
1. Hold the swivelled-up intake grille tight.
2. Align the upper vacuum tube (07/1) to the
housing opening (07/2) as follows:
■
The openings (07/3) of the transverse
grooves and the nubs of the housing
opening (07/4) face each other.
■
The vacuum tube is rotated so that the
two arrows (05/3) and (05/4) are at the
top.
3. Slide the upper vacuum tube (07/1) into the
housing opening (07/2) and rotate it firmly
anti-clockwise until it engages.
Connecting the exhaust air manifold to the
appliance connection piece (08)
1. Align the exhaust air manifold (08/1) to the
appliance connection piece (08/2) so that the
spring (08/3) and groove (08/4) face each
other. The two nubs (08/5) of the exhaust air
manifold must point downwards.
2. Slide the exhaust air manifold (08/1) into the
appliance connection piece (08/2) until it
sticks. The locking catch (08/6) does not en-
gage in the appliance connection piece.
Connecting the collecting sack to the exhaust
air manifold (09)
1. Open the hook and loop fastener (09/1) on
the blow-in opening (09/2) of the collecting
sack.
2. Slide the blow-in opening (09/2) of the col-
lecting sack over the blow-out connection
piece (09/3) of the exhaust air manifold until
the hook and loop fastener (09/1) is located
2500043_a
behind the bulge (09/4). The zip fastener and
carrying belt of the collecting sack must point
upwards.
3. Pull the hook and loop fastener (09/1) tight
and close it.
4. Pull on the collecting sack to check that it is
now firmly connected to the blow-out connec-
tion piece (09/3) of the exhaust air manifold.
5. Close the zip fastener of the collecting sack if
it is open.
Attaching the carrying belt to the collecting
sack (10)
1. Click the snap hooks (10/1) of the carrying
belt in the rings (10/2) on the collecting sack.
2. Pick up the appliance and hang the collecting
sack over your left shoulder. Adjust the
length of the carrying belt by moving the
buckle (10/3) so the collecting sack is com-
fortable to carry.
4.4
Dismantling the collecting sack and the
vacuum tubes
Removing the exhaust air manifold from the
appliance connection piece (11)
1. Pull the exhaust air manifold (11/1) out of the
appliance connection piece (11/2).
It is not necessary to separate the exhaust air
manifold from the collecting sack.
Removing the vacuum tube from the housing
opening (12)
1. Turn the vacuum tube (12/1) firmly clockwise
until it disengages and can be taken off. The
intake grille (12/2) folds shut.
2. Push the intake grille (12/2) against the appli-
ance until it engages.
5 START-UP
5.1
Checking the appliance
Check before starting work:
■
Are all protective grilles undamaged? Have
any damaged protective grilles repaired.
■
Are all screws tight? Tighten any loose
screws.
■
Are the upper and lower handles firmly at-
tached to the appliance? Tighten any loose
handles.
■
Are the shredding blade and the rotor under
the vacuum grille undamaged? Have any
damaged appliance parts repaired.
Autogoods "130"
37
Publicité
