R&G CP0357BL Instructions page 6


Ensure this is mounted correctly before tightening the two bolts to the manufacturers
recommended torque settings. Do not over tighten as damage can occur to the bike.

Now fit the right side metal insert (item 17 – SMW0037) into the recess on the mounting
block, before fitting the remaining two M5 x 6mm long countersunk bolts (item 3) and
tighten, as shown in picture 8.

The crash protector can now be fitted. Slide one of the 12mm washers (item 12) onto the
remaining M12 x 60mm long hexagon headed bolt (item 13) so the washer sits against head of
bolt.

Slide one serrated locking washer (item 11) over the bolt so it sits against the washer just
fitted.

Next slide the bolt with washers through either crash protector (item 2) so head of bolt and
washers goes into counter-bore in bobbin.

Offer the crash protector up to the mounting block and tighten the bolt, as shown in picture 4.

Tighten the bolt until you feel some compression from inside the protector using 19mm socket
and wrench. PLEASE NOTE THE CRASH PROTECTOR MUST BE POSITIONED AS
IN PICTURE 'C' WITH BIGGER END TOWARD FRONT OF BIKE. Turn a little
more so that you feel the compression increase slightly. Then apply a quarter turn. Do not
over tighten as damage can occur to the bike. Do not exceed 40nm of torque.

If not already fitted fit bubble stickers into recess of both crash protector caps.

Fit crash protector caps into both crash protectors.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they
were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be
in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the
gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No
returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not
refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 17/10/2013 (AR)
CONSUMER NOTICE
R&G Racing
www.rg-racing.com Email: info@rg-racing.com