Teka izc 83620 Mode D'emploi page 35

EN
The different power values to which
the hob can be limited will appear
and these can be changed using
the (11) and (10) sensors.
3 Once the value has been selected,
once again press the locking touch
key (6). The hob will be limited
to the chosen power value.
If you want to change the value again,
you must unplug the hob and plug it in
again after a few seconds. Thus you
will again be able to enter the power
limiting menu.
Every time the power level of a
hotplate is changed, the power limiter
will calculate the total power the hob
is generating. If you have reached the
total power limit, the touch control will
not allow you to increase the power
level of that hotplate. The hob will beep
and the power indicator (3) will blink
at the level that cannot be exceeded.
If you wish to exceed that value, you
must lower the power of the other
hotplates. Sometimes it will not be
enough to lower another by a single
level as this depends on the power of
each hotplate and the level it is set at.
It is possible that to raise the level of
a large hotplate that of several smaller
ones must be turned down.
If you use the quick switch-on at
maximum power function and the
said value is above the value set by
the limit, the hotplate will be set to the
maximum possible level. The hob will
beep and the said power value will
blink twice on the indicator (3).
Special functions: CHEF
(depending on the model)
These functions have pre-allocated
power levels to make cooking easier,
obtaining excellent results as the
temperature of the pan is controlled
Fig. 7
34
continuously by sensors. When the
target temperature for the function
has been reached, it is automatically
maintained without needing to change
the power level.
The Chef functions operate correctly
with pans with the same ferromagnetic
area on the base of the pan as the
area of the cooking zone. In addition,
for high temperature functions (above
100ºC), pans must have a flat, even
base (preferably "sandwich" type) as
shown in figure 3.
Fig. 3
To ensure the correct operation of
these functions, it is important that the
pan and the cooking zone are not hot
at the start of the process.
Further information about suitable
pans (saucepans, frying pans, grills,
etc.) is given on the Teka web page.
The Touch Control has special features
that help the user to cook through the
CHEF sensor (16). These functions
are available depending on the model.
To activate a special feature on a zone:
1 First it should be selected; and then,
the decimal point (4) will be active
on the power indicator (3).
2 Now click on the CHEF sensor
(16). The sequentially successive
presses will go over all the CHEF
functions available in each zone
one by one. These functions
will show the activation with the
corresponding leds (17), (18), (19),
(20) and (21).
If you want to cancel a special active
function at any time, you should touch
the "slider" cursor sensor (2) of the
related zone to select it. The decimal
point (4) of the power indicator (3)
will light up. Then, touch again the
"slider" (2) cursor to set a new power
level or to power off the zone, or you
can choose a different special function
touching again on the CHEF sensor
(16).
K E E P W A R M F U N C T I O N
(depending on the model)
This function automatically sets an
appropriate power level to keep the
cooked food hot.
To activate it, select the plate, and
press on the CHEF sensor
until the led (17) located on the icon
/ lights up. Once the function
is activated, the symbol
on the power indicator (3).
You can override the function at
any time by turning off the plate,
by changing the power level or by
choosing a different special function.
MELTING FUNCTION (depending
on the model)
This function maintains a low
temperature in the cooking zone.
Ideal for defrosting food or for slowly
melting other food types as chocolate,
butter, etc.
To activate it, select the plate, and
press on the CHEF sensor
until the led (18) located on the icon
/ lights up. Once the function
is activated, the symbol
on the power indicator (3).
You can override the function at
any time by turning off the plate,
by changing the power level or by
choosing a different special function.
SIMMERING FUNCTION (depending
on the model)
(16)
will appear
(16)
will appear